08 22ssv repower

[ShaunD]

So I bought an 08 22 ssv. No engine or vdrive. Long story short I'm putting a 07 340 monsoon out of a malibu in the boat. Only reason for this is because I couldn't find a turn key assault anywhere. I did call indmar, they assured me this was a plug and play option.

I would like someone with a supra close to that year to supply me with some detailed pictures of the motor mounts, and the brackets for the throttle and transmission. Also is you wouldn't mind I need to put a trim pump. So the location of that would help. The ultra fiberglass silencer that runs horizontal in the back of the engine is missing as well. I can't find one anywhere to save my life.

Thanks for any replies and pictures in advance.

Sent from my SM-G930V using Tapatalk

[docdrs]

Do you have pics of the engine you have and the bay its going into?

[ShaunD]

https://uploads.tapatalk-cdn.com/20170117/b0cea1188d9b5c08c6e336a06e6d9bf6.jpghttps://uploads.tapatalk-cdn.com/20170117/dd988923b7432354f808ade2bb36e15b.jpghttps://uploads.tapatalk-cdn.com/20170117/812a0df61b436a95aa7a17209fc2a801.jpghttps://uploads.tapatalk-cdn.com/20170117/9bea3783e506477710dc1cc0d206ae66.jpg

Sent from my SM-G930V using Tapatalk

[HotWaterMoore]

I can't help with the motor mounts, but I recently ran across this at bakesonline.com.

http://bakesonline.com/detail.aspx?ID=1785

[MJHKnox]

My boat is in storage, but I have to hookup some power for the batteries in the next few weeks.
I have 2007 SSV 22', so I might be able to hook you up.

Mark

[ShaunD]

My boat is in storage, but I have to hookup some power for the batteries in the next few weeks.
I have 2007 SSV 22', so I might be able to hook you up.

Mark
Thanks Mark, that would be great.

Sent from my SM-G930V using Tapatalk

[ShaunD]

I can't help with the motor mounts, but I recently ran across this at bakesonline.com.

http://bakesonline.com/detail.aspx?ID=1785
Thanks for the link.

Sent from my SM-G930V using Tapatalk

[wotan2525]

Have you found a V-Drive?

And what do you mean by trim-pump? There's no trim on these boats (or any other hydraulic accessories that would necessitate a pump.)

I would be very surprised if the Monsoon had any different mounting points than the Assault. I'd add the silent ride muffler if you have space (pretty impressed with how quiet my Malibu is because of that.)

I'm also happy to help if you need the opposite -- I've got a Monsoon in my Malibu and easy access to take photos.

[ShaunD]

Ok. Thanks. The blocks should be identical. They are both general motors blocks. So I'm thinking the mounting points should be the same as well.

I did find a vdrive. 1.5 to 1 walters with vf hurth gear box in front of it.

Sent from my SM-G930V using Tapatalk

[ShaunD]

Thanks Mark, that would be great.

Sent from my SM-G930V using Tapatalk
Mark have you hooked up those batteries yet on your boat?

Sent from my SM-G930V using Tapatalk

[MJHKnox]

Mark have you hooked up those batteries yet on your boat?

Sent from my SM-G930V using Tapatalk
Not yet. Had to take a detour to Utah for some snowboarding. I need to get there this week. I will keep you posted.

Sent from my P00I using Tapatalk

[carlossa]

Hi Shaun
I did a similar swap. Put a 06 Malibu 320LCR in my 04 Launch SSV. I have attached a pic of the mounts. I'm not sure if 08 are the same but 07 definately are.I re-machined everything in stainless as I live on a saltwater lake and they cannot be purchased in stainless. I believe the mounts will be the same. I had a few hurdles to overcome, but it was fairly plug n play. I think you'll find that the throttle will be Drive By Wire. There is plenty of info on the net, you just have to piece it together. While you have the trans disconnected, make sure you replace the pump seal in the front. Its a $10 part that can ruin your day. I'm sure the wealth of knowledge on here will help you out.
http://www.waterskis.com/535000-535-p/engine_mount_front.htm
17937

Regards Carl

[ShaunD]

Hi Shaun
I did a similar swap. Put a 06 Malibu 320LCR in my 04 Launch SSV. I have attached a pic of the mounts. I'm not sure if 08 are the same but 07 definately are.I re-machined everything in stainless as I live on a saltwater lake and they cannot be purchased in stainless. I believe the mounts will be the same. I had a few hurdles to overcome, but it was fairly plug n play. I think you'll find that the throttle will be Drive By Wire. There is plenty of info on the net, you just have to piece it together. While you have the trans disconnected, make sure you replace the pump seal in the front. Its a $10 part that can ruin your day. I'm sure the wealth of knowledge on here will help you out.
http://www.waterskis.com/535000-535-p/engine_mount_front.htm
17937

Regards Carl
Thanks for the pictures Carl. What pump seal are you referring to? The shaft seal ?

Sent from my SM-G930V using Tapatalk

[carlossa]

Hi Shaun
Yes, the input shaft into the trans. If it lets go all your oil is pumped straight out into the bilge and all drive is lost.
Carl

[ShaunD]

Hi Shaun
Yes, the input shaft into the trans. If it lets go all your oil is pumped straight out into the bilge and all drive is lost.
Carl
Oh okay. I'm putting a brand new zf hurth 450 d and a new vdrive in also. There was nothing in the boat when I bought it. Just the main wire harness.

Sent from my SM-G930V using Tapatalk