Tab Content
  • CJD's Avatar
    Yesterday, 07:54 PM
    CJD replied to a thread New owner questions in Service & Repair
    Do you have a heater?
    2 replies | 76 view(s)
  • CJD's Avatar
    Yesterday, 05:05 PM
    CJD replied to a thread Throttle linkage in Service & Repair
    I can't really help you, except to describe what the 2 cables do... One is a straight throttle cable to the carb or throttle body. The second is...
    2 replies | 81 view(s)
  • CJD's Avatar
    04-06-2021, 07:40 PM
    CJD replied to a thread Oil and oil filters in Service & Repair
    I would stick with oil for gasoline engines. Diesels see different contaminants since they burn different fuel. They run slower and see no vacuum...
    2 replies | 88 view(s)
  • CJD's Avatar
    04-01-2021, 10:22 AM
    CJD replied to a thread Bilge Pump Location in Service & Repair
    For 10 years we trailered the boat. Part of the routine was to stop on the ramp and let the bilge drain. Now that it lives on the lake the bilge is...
    6 replies | 124 view(s)
  • CJD's Avatar
    03-31-2021, 06:50 PM
    CJD replied to a thread Bilge Pump Location in Service & Repair
    Thnx...sounds like next seasons upgrade. It is interesting that the factory figured out it was a problem.
    6 replies | 124 view(s)
  • CJD's Avatar
    03-31-2021, 06:48 PM
    CJD replied to a thread Ballast Pump Mounting in General Chat
    I hear ya'! I'll be out working on the dock and those little rats will run back and forth, surfing 100 feet from the floating dock. 3000 acres of...
    54 replies | 2875 view(s)
  • CJD's Avatar
    03-30-2021, 10:59 AM
    CJD replied to a thread Bilge Pump Location in Service & Repair
    I think that is the answer...thanks! Do they have separate outlets in the hull, or the same one? For a single it would take a couple check...
    6 replies | 124 view(s)
  • CJD's Avatar
    03-30-2021, 10:51 AM
    CJD replied to a thread Ballast Pump Mounting in General Chat
    I do. But try to imagine how fast the water will be entering through a 1-1/2" hole. If I don't catch it right away, it may not be possible to get...
    54 replies | 2875 view(s)
  • CJD's Avatar
    03-29-2021, 10:08 AM
    I have never been pleased with the stock location of the bilge pump on our 2005 24SSV. It is toward the rear of the bilge, and as the boat floats...
    6 replies | 124 view(s)
  • CJD's Avatar
    03-29-2021, 10:02 AM
    CJD replied to a thread Ballast Pump Mounting in General Chat
    Wake makers. They advertise a 1" screw fitting for their 1-1/2" bag fitting, so I measured my original bag threads to roughly 1" and thought I was...
    54 replies | 2875 view(s)
  • CJD's Avatar
    03-28-2021, 08:42 PM
    CJD replied to a thread Prop education in General Chat
    I am not running an acme. Glad they stock all the props you need, though.
    9 replies | 189 view(s)
  • CJD's Avatar
    03-28-2021, 08:34 PM
    CJD replied to a thread Ballast Pump Mounting in General Chat
    The HF pump has 1-1/2" inlet/outlet. I'd be willing to bet there would be a difference in flow if using 3/4" plumbing.
    54 replies | 2875 view(s)
  • CJD's Avatar
    03-27-2021, 10:11 PM
    CJD replied to a thread Prop education in General Chat
    It only takes an hour or so to CNC a prop. Why would they backorder?
    9 replies | 189 view(s)
  • CJD's Avatar
    03-26-2021, 11:25 AM
    CJD replied to a thread Ballast Pump Mounting in General Chat
    The hose has an internal teflon wire to keep it stiff...I'm not sure heating would accomplish much with it. It is not going to ever bend much. I...
    54 replies | 2875 view(s)
  • CJD's Avatar
    03-26-2021, 11:13 AM
    CJD replied to a thread Prop education in General Chat
    Prop tech is light years ahead of where it was in 85. I think you will be pleased. And, because there has been so much change, I would recommend...
    9 replies | 189 view(s)
  • CJD's Avatar
    03-22-2021, 07:38 PM
    CJD replied to a thread Blower wonít turn on? in General Chat
    There is a large, 40amp breaker, normally forward of the engine that could have tripped. That one can be reset. The other circuits are fuses,...
    3 replies | 134 view(s)
  • CJD's Avatar
    03-21-2021, 10:40 AM
    +1 for grey.
    8 replies | 518 view(s)
  • CJD's Avatar
    03-20-2021, 10:21 PM
    CJD replied to a thread Ballast Pump Mounting in General Chat
    Alright, here are pics of the super pumps installed. I finally got the boat out for the first run of the season. Those are 1280# bags that fill in...
    54 replies | 2875 view(s)
  • CJD's Avatar
    03-17-2021, 07:17 PM
    CJD replied to a thread Ballast Pump Mounting in General Chat
    47 knot winds right now...you'll have to wait till I get get to the dock!
    54 replies | 2875 view(s)
  • CJD's Avatar
    03-17-2021, 11:17 AM
    CJD replied to a thread Ballast Pump Mounting in General Chat
    The rear 1/3 of the boat looks like new. The upholstery forward will be a gradual project, though. It's all intact, but looks awful next to the...
    54 replies | 2875 view(s)
  • CJD's Avatar
    03-13-2021, 10:37 PM
    That's why I replaced my platform this year...the rubber gets all over swim suites, feet, everywhere. I am sure you can replace the rubber, but the...
    5 replies | 170 view(s)
No More Results
About CJD

Basic Information

Statistics


Total Posts
Total Posts
599
Posts Per Day
0.23
General Information
Last Activity
Yesterday 07:54 PM
Join Date
12-27-2013
Referrals
0

1 Friend

  1. stuartburchill stuartburchill is offline

    Junior Member

    stuartburchill
Showing Friends 1 to 1 of 1