Search:

Type: Posts; User: h2o-ski

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Good to hear that you got some time to get away. ...

    Good to hear that you got some time to get away. Props to the shop, their work is top notch.
  2. Replies
    2
    Views
    121

    On my last boat, at idle the water pump sucks...

    On my last boat, at idle the water pump sucks less water than what the hose flows. 1800 rpms would be close to the flow from the hose.

    If water is coming out the exhaust, your raw water pump is...
  3. Hey Mischief, Do you have any updates on your...

    Hey Mischief,

    Do you have any updates on your restore? I have just about run out of popcorn and I want to see how it comes out. :)
  4. Replies
    2
    Views
    93

    I roughly priced what it would take to put in an...

    I roughly priced what it would take to put in an LS vs rebuild the SBC in mine.

    Just about all the marinization companies (PCM, Crusader, Marine Power) offered the 6.0L in the mid to late 2000's...
  5. Replies
    43
    Views
    33,987

    Here is the way I broke it down: Wood vs...

    Here is the way I broke it down:
    Wood vs composites
    - Do you want the boat to last more than your lifetime guaranteed?
    Yes - composite
    No - Wood, though when done properly wood can last a...
  6. Replies
    43
    Views
    33,987

    Seems like I take 3 steps forward and 2 steps...

    Seems like I take 3 steps forward and 2 steps back.
    Went to secure the cap to the hull and either the cap shrunk or the hull grew in the bow. I ripped out the floor and stringers in the bow to give...
  7. Replies
    33
    Views
    12,777

    I'm glad you were able to make the most of it. ...

    I'm glad you were able to make the most of it. Kinda glad my rebuild was not complete yet. At some point I would like to attend a meetup or Supra reunion.

    Any clue why most boater reunions are...
  8. First off beautiful boat. I count 7 possible...

    First off beautiful boat.

    I count 7 possible aftermarket modifications, not including your phone. Though I would not call myself a guru or expert on early Supras.

    Sent from my SM-G950U using...
  9. Replies
    43
    Views
    33,987

    Despite record heat here in Texas work continued....

    Despite record heat here in Texas work continued. Deck is done and cap is placed on the hull. I'm glad I test fit the cap as it looks like I knew what I was doing. eBay Seadek went on sale and I...
  10. My 2 cents is, don't wait to long before...

    My 2 cents is, don't wait to long before beginning the restore. Reason being is that if you wait too long, it will be hard to make replacement parts when the originals are turned to dust. For my...
  11. Replies
    4
    Views
    285

    There could be a number of different locations...

    There could be a number of different locations that water could be leaking. While it could be the shaft packing, it could also be leaking exhaust, rudder port or leaking water hose.

    Best bet is...
  12. Replies
    3
    Views
    947

    I would check Acme propeller as they have a prop...

    I would check Acme propeller as they have a prop selector tool that will help find the prop based on the parameters you give it. Or I have heard that OJ props has great customer support. Also...
  13. Replies
    43
    Views
    33,987

    Work continues. Got the flooring faired and just...

    Work continues. Got the flooring faired and just have to sand a few spots smooth. I got the bilge and pylon holes cut. With all this recent progress I feel like I am actually working on a boat and...
  14. Replies
    3
    Views
    947

    A Borg Warner Velvet Drive 71c would have been...

    A Borg Warner Velvet Drive 71c would have been the transmission used. What prop are you using? It would be much cheaper to put a lower pitched prop on than trans and prop.
  15. Replies
    43
    Views
    33,987

    With the kids of on summer break, I've been able...

    With the kids of on summer break, I've been able to put some serious work done.

    The deck has had the corners rounded over and a coat of resin on all sides. I also got the battery access cut. Not...
  16. Replies
    43
    Views
    33,987

    I put the cap on one last time to make sure...

    I put the cap on one last time to make sure everything is at the correct height. For the most part it is dead on. There in only one area where I need to shim the floor up 1/8".

    I was able to...
  17. Replies
    3
    Views
    374

    I personally would not unless you are ready for...

    I personally would not unless you are ready for an extensive project or you have been waiting for that boat model. From the description it is a complete gut job and rebuild much like what I am in...
  18. Replies
    43
    Views
    33,987

    Status update: 3/4" BCX plywood hurt the...

    Status update: 3/4" BCX plywood hurt the pocketbook at $70 a sheet, but progress must continue. 90% of the flooring has been cut to size. I just have the area under the helmet to cut.

    I took...
  19. Replies
    43
    Views
    33,987

    Progress is picking up. I cut up my old pylon...

    Progress is picking up. I cut up my old pylon assembly to free the original pylon and also to use the sides for backers for the new assembly. I also picked up most of the plywood flooring and...
  20. Replies
    43
    Views
    33,987

    Progress has been slow but still making it. I got...

    Progress has been slow but still making it. I got the exhaust hose in and setup.

    A family event put me in the general area of the legendary Mischief. So it was decided we should perform a...
  21. Replies
    43
    Views
    33,987

    Well onto set back #164 (exaggerating but not by...

    Well onto set back #164 (exaggerating but not by much). I noticed that the base for the pylon was still flaking off after I got it to bare metal before I painted it. After further inspection, I'm...
  22. Replies
    43
    Views
    33,987

    Here are some pictures of the cap repair. There...

    Here are some pictures of the cap repair. There was far more repair work on where the cap and the storage locker meet but due to how I have the cap supported I can't get a good picture of it.
    ...
  23. Replies
    43
    Views
    33,987

    The floor that I pulled out was 3/4" marine ply. ...

    The floor that I pulled out was 3/4" marine ply. My uncle replaced the floors after he got it because they rotted out back then. The cap has been back on the hull 3 times to make sure there is room...
  24. Replies
    43
    Views
    33,987

    Progress report Built bulkheads to help prevent...

    Progress report
    Built bulkheads to help prevent water intrusion and support the floor. I have 3/4" flooring planned.
    I placed the cap on one more time and everything looks to be close. So far the...
  25. Thread: 87 Ts6m Parts

    by h2o-ski
    Replies
    6
    Views
    2,821

    Thank you for the bolt spacing. I will measure...

    Thank you for the bolt spacing. I will measure shortly and get back with you
Results 1 to 25 of 48
Page 1 of 2 1 2