Search:

Type: Posts; User: nick 55

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    8,891

    Rough area to get to. You’ll need skinny arms to...

    Rough area to get to. You’ll need skinny arms to wipe down the bottom of the oil pan and hose coming out of it to clean the area for inspection. Then you’ll need to monitor it after a little bit...
  2. Replies
    2
    Views
    1,495

    Much like h2o said, it doesn’t take much. I...

    Much like h2o said, it doesn’t take much. I would also check your engine mounts as well as engine to shaft alignment. It’s not hard but it is kind of cumbersome working around the transmission to...
  3. Replies
    1
    Views
    1,043

    Wakemakers has a chart of recommended props. ...

    Wakemakers has a chart of recommended props. Seems all of the mid-2000’s V drive Supras all use similar props and all are Acme props. If you would have bought 2 years ago, the prices would have...
  4. Replies
    2
    Views
    3,593

    I would be very surprised if a Raptor engine fit...

    I would be very surprised if a Raptor engine fit in the same space width-wise. Not only size but you’ve got a whole bunch of integration concerns to deal with and this could easily exceed the cost of...
  5. Replies
    8
    Views
    4,578

    Look what I found on my local Craigslist…. A TS6M...

    Look what I found on my local Craigslist…. A TS6M getting parted out. This would be what you need right?
    https://milwaukee.craigslist.org/bpo/d/antioch-1985-supra-ts6m/7585570282.html
  6. Replies
    8
    Views
    4,578

    Those factory glass pieces will be unobtanium at...

    Those factory glass pieces will be unobtanium at this point. Since they are flat glass, just about any local glass shop can cut you tempered glass to fit, and will likely be able to get shading real...
  7. Replies
    9
    Views
    3,313

    Thanks, this helps me with what shape I think I...

    Thanks, this helps me with what shape I think I need.
  8. Replies
    9
    Views
    3,313

    1992119922199231992419925 The finishing cap has...

    1992119922199231992419925
    The finishing cap has an internal height of 1.554", and in the top of that there is a small cut out that is .375" deep, where the internal depth is 1.270". The depth of...
  9. Replies
    9
    Views
    3,313

    First batch. 1991619917199181991919920

    First batch.
    1991619917199181991919920
  10. Replies
    9
    Views
    3,313

    No but I can go out and take the finishing piece...

    No but I can go out and take the finishing piece off the stern and take one side up to take measurements and pics.
  11. Replies
    9
    Views
    3,313

    Thanks Mischief, I was looking at the Taco...

    Thanks Mischief, I was looking at the Taco Suproflex because it looks the closest profile but I would appreciate any feedback of supplies you’ve used. Taco said they would not sell me any samples...
  12. Replies
    9
    Views
    3,313

    Santera rub rail supplier?

    Hey everyone. Iíve got a 2000 Santera that has given us lots of good times on the water and Iíve done a lot of work making it a solid boat. Still need to fix up a few items, and one of them is the...
  13. Replies
    3
    Views
    1,325

    Get yourself an old school test light (12V...

    Get yourself an old school test light (12V incandescent light in a screwdriver handle with a pointed tip and a ground wire). Start by checking across the battery, then leave the ground clamp on the...
  14. Replies
    1
    Views
    434

    You mean the log that has raw water flow through...

    You mean the log that has raw water flow through it and two oil lines on the side? If so, measure the length and oil line fitting size. Skidim has most sizes in stock.
  15. Replies
    4
    Views
    2,600

    Start with the power issue. Fuel pumps use a...

    Start with the power issue. Fuel pumps use a decent amount of current, more than an ECU. So if you lose battery power, things like fuel pumps will stop working. Loose battery connections or...
  16. Replies
    1
    Views
    4,002

    Check out Ron Tanis, he’s got a Medallion gauge...

    Check out Ron Tanis, he’s got a Medallion gauge replacement kit that works good. My boat has it (2000 Santera).
  17. Replies
    4
    Views
    839

    I don’t know why it didn’t ever post when I...

    I don’t know why it didn’t ever post when I replied to this a week ago, but I have a Santera that had Tanis’ update done before I bought it. Definitely wasn’t a bad job to do (I looked it over) and...
  18. Replies
    3
    Views
    2,212

    I just went through this same task this afternoon...

    I just went through this same task this afternoon on my Santera. I found a video on YouTube from SkiDIM (Discount Inboard Marine) that was helpful for me. They pointed me to those videos when I...
  19. Replies
    4
    Views
    589

    I don’t have a 99, but I do have a 2000. There...

    I don’t have a 99, but I do have a 2000. There is no in tank fuel pump on mine. The pickup and return feeds are plumbed in through the top and only the level sensor is in the tank. If it is like...
Results 1 to 19 of 20