Search:

Type: Posts; User: skiman_61

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    20
    Views
    1,884

    I've been told that they're stainless. They do...

    I've been told that they're stainless. They do have a seam, though, and I think that may be the issue.

    Used the same holes, caulked them good.

    The floor does go all the way back. I was...
  2. Replies
    20
    Views
    1,884

    UPDATES: I still have water coming in just under...

    UPDATES: I still have water coming in just under the exhaust pipe as can be seen in my last pic. I spoke with Vince at SKIDIM about the issue. He related that one other person in his experience...
  3. Replies
    20
    Views
    1,884

    Sealed the swim platform mounts today. Letting it...

    Sealed the swim platform mounts today. Letting it cure.
  4. Replies
    1
    Views
    285

    Gasket seated?

    Gasket seated?
  5. Replies
    20
    Views
    1,884

    Redid all the caulk around the exhausts. Let it...

    Redid all the caulk around the exhausts. Let it cure as recommended. Still have water coming in. I'll pull the ski, platform this week and caulk the begets out of those holes. Water is appearing...
  6. Replies
    20
    Views
    1,884

    Yes, I should have taken more pics. I pulled all...

    Yes, I should have taken more pics. I pulled all the old caulk. Those gaps around the pipe have to be where the water was getting in. Can’t imagine where else?
  7. Replies
    20
    Views
    1,884

    The pipes in my '87 meet the transom to within a...

    The pipes in my '87 meet the transom to within a millimeter. (see pics) I would not go to the trouble of removing the gas tank, as I did for deck replacement, just to mess with the pipes. My flange...
  8. Replies
    20
    Views
    1,884

    Pics

    Pulled the baffles, here's what I found. Big gaps in the caulk. Figure if I clean and seal and put back I ought to be good.
  9. Replies
    20
    Views
    1,884

    I concur.

    The design does suck, directed the concussive force of the exhaust back at the hull and the thin seal with hot water.

    So, what'd you replace them with and how?

    Thanks,

    Jack
  10. Replies
    20
    Views
    1,884

    Hey guys, got the boat back from my fiberglass...

    Hey guys, got the boat back from my fiberglass guy. New floor. Original stringers solid. I’ve got water coming in around my pipes like you wouldn’t believe. I need to caulk the interior of the tubes?...
  11. Replies
    7
    Views
    876

    Thanks, Cooose. They come in varying lengths at...

    Thanks, Cooose. They come in varying lengths at integrity. I should read more carefully.
  12. Replies
    7
    Views
    876

    I'm measuring 23' down the side x 2 = 46'. Add...

    I'm measuring 23' down the side x 2 = 46'. Add 6' for the stern that'd be 52'. Where you getting 70'?
  13. Replies
    7
    Views
    876

    Thank you!

    Thank you!
  14. Replies
    7
    Views
    876

    Saltare' '87 RUB RAIL

    Hey brothers,

    In all of the rehabilitation going on with my precious.........old Salt, I am going to have to replace the bumper strip. Where to get another? Just need the rubber if that's an...
  15. Replies
    5
    Views
    724

    That sounds like a good idea. I've got a larger...

    That sounds like a good idea. I've got a larger (8") screw cap access. The stock cap has always been a pain.
  16. Replies
    5
    Views
    724

    Thanks. Don’t need to stand up under it, but...

    Thanks.

    Don’t need to stand up under it, but it would be nice to have a bit of space above the windscreen.

    If I still had my 16 year old arms the bilge access wouldn’t be as much of an issue....
  17. Replies
    5
    Views
    724

    Bimini tops and bilge accesses.

    Hey guys,

    I'm thinking to replace my convertible top with a bimini so as to be able to walk under it and have a greater shade area in the boat. Tips from those who've put one on? What would you...
  18. Replies
    20
    Views
    1,884

    The brackets look to be sealed tighter than a...

    The brackets look to be sealed tighter than a duck's butt. Then again, water can find a way. Thanks for the tip!

    Jack
  19. Replies
    20
    Views
    1,884

    I put it pretty far up in there. Not sure I knew...

    I put it pretty far up in there. Not sure I knew there was a joint at 4" tho.

    Thanks for the response.
  20. Replies
    20
    Views
    1,884

    Water leak '87 Salt

    Hey guys,

    I've had water coming into my old salt coming up around my exhaust tubes. I removed the baffles and caulked the bejesus out of the tubes two seasons ago. No change. The only thing I...
  21. Replies
    2
    Views
    515

    Thanks. Had it out several years ago. Figured it...

    Thanks. Had it out several years ago. Figured it out. Access opening behind the side pad and two screws in the back side from storage.
  22. Replies
    2
    Views
    515

    Saltare’ 87 seats

    Hey gents,

    Can’t remember how to remove the observer seat. Help a brother out?

    Thanks!

    Jack
  23. Replies
    18
    Views
    1,445

    Happy 4th, everyone. Safe boating!

    Happy 4th, everyone. Safe boating!
  24. Replies
    18
    Views
    1,445

    Thanks. Also, staring at the block I see that...

    Thanks. Also, staring at the block I see that the firing order is in the casting on top of the motor. Almost 20 years I've been fooling with this thing and never noticed that.
  25. Replies
    18
    Views
    1,445

    Thanks sincerely for all the help. I pulled the...

    Thanks sincerely for all the help. I pulled the raw water pump again and found an obstruction. I'll explain once I figure it out. Recall I previously pulled all the water lines and found them to be...
Results 1 to 25 of 220
Page 1 of 9 1 2 3 4