Search:

Type: Posts; User: angus2112

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    8,289

    interested in buying the boat with a bad engine

    interested in buying the boat with a bad engine
  2. Replies
    10
    Views
    8,289

    where are you at and how much do you want for it...

    where are you at and how much do you want for it shoot me a pm
  3. Replies
    1
    Views
    3,371

    have interior out of a 87 salt pretty sure some...

    have interior out of a 87 salt pretty sure some will fit also in north west Ohio south east Michigan nearest town is Metamora Ohio pm me if interested not sure what i have will have to look
  4. Replies
    9
    Views
    1,429

    yes the cap was off new stringer were all glassed...

    yes the cap was off new stringer were all glassed in
  5. Replies
    9
    Views
    1,429

    please don't lift it like i did that was a roll...

    please don't lift it like i did that was a roll over for paint after a stringer job
  6. Replies
    9
    Views
    1,429

    I did pretty sure that's how they did it at the...

    I did pretty sure that's how they did it at the factory 19534
  7. Replies
    7
    Views
    1,420

    did you get rid of the ballast resistor and run...

    did you get rid of the ballast resistor and run 12 volts direct to the coil not knowing what ohm coil you are running if you have 12v going to it all the time you can burn it up get the right flame...
  8. Replies
    63
    Views
    68,095

    try ski dim

    try ski dim
  9. i have a intake you can have just pay shipping as...

    i have a intake you can have just pay shipping as far as the exhaust drill the end of the cracks v the cracks and use jb weld did it pop any soft plugs
    Weak spot on a sbf right side front lower...
  10. Replies
    3
    Views
    1,385

    i might have 1 when i rebuilt mine i made doubles...

    i might have 1 when i rebuilt mine i made doubles of most of the wood for patterns modeled my salt seat after it 19267
  11. Replies
    4
    Views
    1,266

    the super traps are the only thing that holds the...

    the super traps are the only thing that holds the ex pipe in it is a wedge fit if you remove them there is nothing to keep the pipe tight ie water leak
    if you want it louder put stainless washers...
  12. Replies
    13
    Views
    64,592

    run a r45ts ac delco or if you want to spend more...

    run a r45ts ac delco or if you want to spend more money mr45ts
    are you running points any coil up grade ?
    buy the looks getting the right plugs will clear up your carbon issue
  13. Replies
    18
    Views
    37,314

    I use 1/2 marine on the outside stringer rip it 8...

    I use 1/2 marine on the outside stringer rip it 8 ft long glue together stagier the seams every 4 ft
    inside stringer i 1 peace it using lvl or lam beams full 2 inch
  14. Replies
    4
    Views
    2,067

    there is no gasket between the trans and the...

    there is no gasket between the trans and the engine most likely the front pump seal
  15. Replies
    6
    Views
    2,271

    do you want all the glass pm me

    do you want all the glass pm me
  16. Replies
    6
    Views
    2,271

    I have a complete set of glass for a salt no frame

    I have a complete set of glass for a salt no frame
  17. Replies
    6
    Views
    2,271

    They are taylor made you can still get parts...

    They are taylor made you can still get parts mostly seals. I have a complete set of glass for a salt if anyone needs them. Chopped 6 in out of mine19099
  18. Replies
    10
    Views
    34,816

    2 school's out there. To foam or not to foam be...

    2 school's out there. To foam or not to foam be it nobler to obey all the coast guard laws or save the labor of not doing stringers again ( enough shakespeare ) i dont foam. at the end of the day it...
  19. Replies
    6
    Views
    2,180

    19037 fill it with foam shape it off put 2-3...

    19037 fill it with foam shape it off put 2-3 layers of 1708 over it to seal the foam
  20. Replies
    13
    Views
    3,635

    Do it i put a solid mahogany floor in my salt...

    Do it i put a solid mahogany floor in my salt changing all the teak and adding more mahogany 18655
  21. Replies
    105
    Views
    48,517

    you should be able to get them from skiers choice...

    you should be able to get them from skiers choice there was something a few years back where they sent new ones out ( i think i still have them ) for some kind of up grade i will look in my book when...
  22. Replies
    15
    Views
    3,681

    i will pull it out tonight take some pic and get...

    i will pull it out tonight take some pic and get the part number off it
  23. Replies
    15
    Views
    3,681

    I have a orignal off a pcm that could be yours

    I have a orignal off a pcm that could be yours
  24. Replies
    7
    Views
    3,286

    www.integritymarinecorp.com good people to work...

    www.integritymarinecorp.com good people to work with just bought some for my salt i think it was $300.00 for everything
    .
  25. Replies
    45
    Views
    80,240

    use 1708 glass round the top of the stringers and...

    use 1708 glass round the top of the stringers and make a nice round transition (fillet) where the the stringer meets the hull i use liquid nails it takes some time to dry but does not shrink like pl...
Results 1 to 25 of 77
Page 1 of 4 1 2 3 4