Search:

Type: Posts; User: csuggs

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    2
    Views
    72

    The size should be stamped somewhere on the prop....

    The size should be stamped somewhere on the prop.

    Sent from my SM-G973U using Tapatalk
  2. Thread: Prop Questions

    by csuggs
    Replies
    3
    Views
    146

    Never heard of a 14" diameter prop on a Supra...

    Never heard of a 14" diameter prop on a Supra [emoji848] but then again ....
    I'm like you, most of what I've seen on the older Supra models like ours was 13" diameter. 13x13 was very common from...
  3. Thread: Prop education

    by csuggs
    Replies
    10
    Views
    709

    My experience, for what it's worth. 86...

    My experience, for what it's worth. 86 Sunsport, 351, 1:1 Velvet Drive. Original prop was a Michigan Wheel 13x13 3-blade. I tried the 4-blade which gave me better hole-shot but no top-end. ...
  4. Replies
    11
    Views
    869

    Buffing and polishing is done!! The "other woman"...

    Buffing and polishing is done!! The "other woman" is naked and clean! [emoji57] Next is a coat of wax and new...
  5. Replies
    6
    Views
    365

    I used to run a 160degree thermostat in my 351W...

    I used to run a 160degree thermostat in my 351W and it always indicated in the 170s. Either Vince or Rich at skidim had me install a 145degree thermostat and now the gauge sits right on 160, which...
  6. Replies
    52
    Views
    37,607

    Some of the original Supras used a packing gland,...

    Some of the original Supras used a packing gland, others had a mechanical seal with o-rings, grease seals and snap rings holding it together. Mine is the latter, and somewhere there's an old thread...
  7. Replies
    11
    Views
    869

    The boat was suspended by overhead shop cranes in...

    The boat was suspended by overhead shop cranes in the pic. I blocked it up before I got under it. Meguiars has a 3 part marine restoration product.
    ...
  8. Replies
    11
    Views
    869

    A quick update. Trailer is finished .. may as...

    A quick update. Trailer is finished .. may as well be a new one. Sandblast and epoxy paint, new brake actuator, new brake lines, new brake backing plates, new bearings and races, new wiring and...
  9. Replies
    20
    Views
    4,385

    I have one for an 86 Sunsport if that helps. ...

    I have one for an 86 Sunsport if that helps.

    Sent from my SM-G973U using Tapatalk
  10. Thread: Prop education

    by csuggs
    Replies
    10
    Views
    709

    What motor and tranny? Sent from my SM-G973U...

    What motor and tranny?

    Sent from my SM-G973U using Tapatalk
  11. Replies
    4
    Views
    753

    New Coast Guard Requirement

    Seriously? Check this out. Who's behind this and why do they think we need to idiot-proof everything?
    ...
  12. Replies
    31
    Views
    7,468

    I think you're probably right. Sent from my...

    I think you're probably right.

    Sent from my SM-G973U using Tapatalk
  13. Thread: Strut bushing

    by csuggs
    Replies
    3
    Views
    310

    I'm thinking it is two pieces, each held in with...

    I'm thinking it is two pieces, each held in with a set screw. At least that's what I remember when I did mine.

    Sent from my SM-G973U using Tapatalk
  14. Replies
    7
    Views
    466

    This is the same as what I did on my 86 years ago...

    This is the same as what I did on my 86 years ago and it works great! FYI, at first I only replaced the points with Pertronix ignition, but it never ran really good until I installed the Flame...
  15. Replies
    11
    Views
    869

    [emoji1787] Sent from my SM-G973U using...

    [emoji1787]

    Sent from my SM-G973U using Tapatalk
  16. Replies
    11
    Views
    869

    Thanks, will do!! Sent from my SM-G973U...

    Thanks, will do!!

    Sent from my SM-G973U using Tapatalk
  17. Replies
    11
    Views
    869

    Shiny! The bottom looks so good I need to do the...

    Shiny! The bottom looks so good I need to do the sides now. ...
  18. Replies
    3
    Views
    255

    I'm using Meguiars. Sent from my SM-G973U...

    I'm using Meguiars.

    Sent from my SM-G973U using Tapatalk
  19. Replies
    5
    Views
    361

    Yes, I talked to Mike Gibbs and order the Supra...

    Yes, I talked to Mike Gibbs and order the Supra Logo.

    Sent from my SM-G973U using Tapatalk
  20. Replies
    5
    Views
    361

    Hey Breezy! Pics when it's done. I did order...

    Hey Breezy! Pics when it's done. I did order the fender grips from Gatorstep.

    Sent from my SM-G973U using Tapatalk
  21. Replies
    11
    Views
    869

    Forgot to add the before pic...

    Forgot to add the before pic ...https://uploads.tapatalk-cdn.com/20210301/fb41b184e77d0ce94f8d176310763c1b.jpg

    Sent from my SM-G973U using Tapatalk
  22. Replies
    11
    Views
    869

    Bottom Maintenance

    This is a project that I have put off for years. I had my trailer sandblasted and painted this month so I figured the time for buffing below the waterline had finally come. Pics are after using 3M...
  23. Replies
    5
    Views
    361

    Non-slip fender grip for trailer

    Anyone know where I could get non-skid grip tape like seadeck or gatorstep that I can put on the top of my trailer fenders, preferably Supra logo? I just had my trailer sandblasted and painted.
  24. Replies
    31
    Views
    7,468

    Interesting ... I read the article 10 years ago. ...

    Interesting ... I read the article 10 years ago. Still interesting.
  25. Replies
    41
    Views
    9,594

    1581815819 Finally got "the other woman" back...

    1581815819

    Finally got "the other woman" back in the water over Memorial Day Weekend! The transom repair went really well and there is no longer any flex in the transom from the swim platform! ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4