Search:

Type: Posts; User: Cusefan78

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds; generated 36 minute(s) ago.

  1. Replies
    0
    Views
    197

    Gt40 stalling after warm

    Hey everyone. 1995 labrisa with a gt40 in it. Boat runs and starts great. After 20 mins of use the boat stalls and will restart instantly. It’ll be going and idles down then stalls. Any insight would...
  2. Replies
    3
    Views
    1,781

    Could be anything. You'll need to test the wires....

    Could be anything. You'll need to test the wires. Gauge could be bad or could be a loose connection
  3. Make sure you get marine parts. I get all my...

    Make sure you get marine parts. I get all my stuff through skidim
  4. Thread: Gas Gauge

    by Cusefan78
    Replies
    2
    Views
    1,177

    Make sure there isn't wax build up or debris on...

    Make sure there isn't wax build up or debris on the vent. Had that happen to me once
  5. Let me know. My high pressure pump went bad last...

    Let me know. My high pressure pump went bad last year and found the part was updated and the new pump wasn't right. Had to track down another manufacturer that made the same pump
  6. Replies
    5
    Views
    1,610

    The hole shot is nice. Last year I pulled 20...

    The hole shot is nice. Last year I pulled 20 older heavy guys out of the water back to back and no one had a problem getting out. The other thing to check is the wake plate. There is a write up on...
  7. Ok then find the fuel return line. Pinch it...

    Ok then find the fuel return line. Pinch it closed and see if it runs better. If it does one of your pumps was defective.
  8. Have you changed the canister filter.

    Have you changed the canister filter.
  9. Replies
    5
    Views
    1,610

    My labrisa has the 541 on it. I get 48 at wot....

    My labrisa has the 541 on it. I get 48 at wot. Never had a problem with
    Torque since I changed to it. As for the cavitation are you sure it's not the tranny starting to slip. I had the exact issue...
  10. I had an issue last year with the pump going bad....

    I had an issue last year with the pump going bad. Check the relay to see if it's energized if you have power then it's the pump. There are two. A low pressure and high. I believe it was the high then...
  11. It's on the back of the motor where the breakers...

    It's on the back of the motor where the breakers are. You'll see the relays attached to the metal bracket
  12. Let me know if you have any questions

    Let me know if you have any questions
  13. If you have it apart already and there is any...

    If you have it apart already and there is any sign of wear I would do a rebuild. Discs and seals aren't that much and it's only a few hour job. Just be careful with the spring. Make sure you...
  14. 18147 a new disc is 2mm thick. What usually...

    18147 a new disc is 2mm thick. What usually happens. Is they will either glaze over from spinning or the inside teeth wear out. I have rebuilt two of them. Pretty easy to do. I did a write up on here...
  15. What's it doing? Oil have a burnt smell? The...

    What's it doing? Oil have a burnt smell? The discs are easy to tell if they are bad. I'll look for a few new ones I have and mic them for you.
  16. Replies
    2
    Views
    1,227

    Yeah I called them yesterday. Only offer my color...

    Yeah I called them yesterday. Only offer my color in a 1 gallon size. I picked up a kit today and going to bench mix it.
  17. Replies
    2
    Views
    1,227

    Gelcoat patch

    Does anyone know of a company that sells a premixed gelcoat kit other then spectrum. With the high waters something rubbed against the side of my labrisa and I have a 1"X1/4" scratch that's into the...
  18. Replies
    2
    Views
    1,123

    Thanks mike

    Thanks mike
  19. Replies
    2
    Views
    1,123

    Fuel separator element

    Anyone know the fram fuel element number that fits in that orange canister. I left my cottage without looking for the number and I need a new one.
  20. If you go to the service tab there is a prop...

    If you go to the service tab there is a prop page. Lots of info there. Here is a good page also. https://www.wakemakers.com/supra-wakeboard-boat-propellers I'm running a 541 and love it. I got a...
  21. exactly. Honestly most people are going to look...

    exactly. Honestly most people are going to look at a nada guide. Also you have another thing keeping from geting top dollar, the long cold winter that is quickly approaching. Most people aren't in...
  22. So is your number 15k? Really hate when people do...

    So is your number 15k? Really hate when people do this. You have a number in your head just post it. It's a nice looking boat!
  23. Replies
    11
    Views
    66,564

    Go big or go home. Get one of these and you can...

    Go big or go home. Get one of these and you can never blame missing a ball on the ski again.
    ...
  24. Replies
    11
    Views
    66,564

    I went ten years without upgrading my old ho...

    I went ten years without upgrading my old ho skis. I was running a monza and a system 8. a few years back I picked up a left over strada. Killer ski! Crazy how much technology has advanced the skis....
  25. Thread: Ride steady

    by Cusefan78
    Replies
    28
    Views
    43,020

    Sorry I just saw this. I'll be back up to my boat...

    Sorry I just saw this. I'll be back up to my boat tomorrow and I'll look at my setting.
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4