Search:

Type: Posts; User: Tonymozingo

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    841

    Throttle linkage

    Hi, Well, I was trying to get my '86 Conbrio running but the carburetor was fouled. And yes, I made the mistake of pouring a little gas into it. And yes, the carb. caught on fire.
    The damage is...
  2. Replies
    10
    Views
    12,094

    Tried 30 mins to figure out how to send a pic to...

    Tried 30 mins to figure out how to send a pic to no avail. I’ll report back later. Thanks for hanging in there with me.
  3. Replies
    10
    Views
    12,094

    Ok. Thanks. I’ll check both. Where is...

    Ok. Thanks. I’ll check both.
    Where is thermostat located?
  4. Replies
    10
    Views
    12,094

    351W PleasureCraft overheating...

    First, thanks to all who contributed advice as I rebuilt an ‘86 over the winter. It runs well. However, I have a new problem.
    The engine overheats soon after cranking. I replaced the impeller and...
  5. Replies
    2
    Views
    11,554

    Please help me

    Please help me
  6. Replies
    2
    Views
    11,554

    351 PC Windsor Wiring question

    I’ve installed new carb, new distributor, fuel line, filter and pump, plug wires, plugs, and wiring harness. I think I have it wired up correctly and I have it 8 degrees before TDC. I have the rotor...
  7. Replies
    1
    Views
    15,512

    351 Windsor PC Distributor housing

    Trying to delete post
  8. Replies
    1
    Views
    11,044

    Setting Timing-351 Windsor PC

    I’ve received my new distributor and carb and am ready to attempt setting the timing. I’d appreciate someone helping me or referring me to a site I can go to for learning how.
    Is there a tutorial...
  9. Replies
    5
    Views
    19,724

    I am so glad for this advice. There’s no sludge,...

    I am so glad for this advice. There’s no sludge, but whatever additive or ? The previous owner put in definitely broke down. The fuel has a peculiar smell and a reddish tint. I’d hate to know I ran...
  10. Replies
    5
    Views
    19,724

    Any tips on siphoning? I can’t get the...

    Any tips on siphoning? I can’t get the remainder; it’s still half full. Is there a certain shape of the tank preventing the hose from reaching deep enough?
  11. Replies
    5
    Views
    19,724

    Old gas; 351 PCM

    89 Supra has been on rack for ten years. Almost full of gasoline.
    I’m installing a new carb.
    Question: Is there a reasonably easy way to drain the old gas from the tank, and if not, what should I...
  12. Replies
    8
    Views
    17,012

    I took your advice and ordered from Skidim. Great...

    I took your advice and ordered from Skidim. Great folks. New carb and distributor coming. Thanks again
  13. Replies
    8
    Views
    17,012

    Maybe I should dismount and replace the one I...

    Maybe I should dismount and replace the one I bought
  14. Replies
    8
    Views
    17,012

    You won’t believe this, but I threw the old one...

    You won’t believe this, but I threw the old one away.
    I am so ignorant to do that.
    Any other suggestions? I get what you said about the wires and manual choke
  15. Replies
    8
    Views
    17,012

    Thanks, Michael. One last question and I’ll...

    Thanks, Michael.

    One last question and I’ll stop bothering.
    I bought a Holley carb to replace the old and when I mounted it, I noticed it did not have the two prongs for the pos and neg elect....
  16. Replies
    8
    Views
    14,072

    Hattiesburg, MS

    Hattiesburg, MS
  17. Replies
    8
    Views
    17,012

    ‘89 Supra Ford 351 Windsor Distributor

    Starting this thread because I need the info. ASAP.
    Thanks in advance.

    I’m replacing the distributor because it had points. Took the old one out already.
    What are the parts ID numbers for new...
  18. Replies
    8
    Views
    14,072

    Yes. So I took the entire distributor out and am...

    Yes. So I took the entire distributor out and am looking to replace the old with new.
    Would you please advise where and how to order a new distributor and cap,etc?
    My O’Reilly’s guys can’t find...
  19. Replies
    8
    Views
    14,072

    Man, that must be it. The wire from the dist. cap...

    Man, that must be it. The wire from the dist. cap was melted onto the coil and half that bond looks burnt.
    I really appreciate it, sir.
  20. Replies
    8
    Views
    14,072

    That’s it! Could that be the reason I’m not...

    That’s it! Could that be the reason I’m not getting spark to the plugs?
  21. Replies
    8
    Views
    14,072

    Part Identification and assistance needed

    Hi, I have an ‘89 Supra 351
    PleasureCraft. It’s been sitting for many years. I have it turning over and have determined it’s not firing.
    I suppose I’m correct in replacing the next part down the...
  22. Replies
    0
    Views
    617

    Wanted- Swim platform for 1998 Supra

    I want to buy a platform and brackets for my Supra. The original was white fiberglass or plastic.
  23. Replies
    7
    Views
    18,054

    Crystal, That’s is the same boat model and color...

    Crystal, That’s is the same boat model and color as mine.

    1989 Supra PleasureCraft 351

    I’m happy to report through the members of this forum, I’ve gotten it wired correctly. Thank you.
    ...
  24. Replies
    7
    Views
    18,054

    https://forum.supraboats.com/images/attach/bmp.gif

    https://forum.supraboats.com/images/attach/bmp.gif
  25. Replies
    7
    Views
    18,054

    Many thanks sir. It’s A pcm 351. Supra. I think...

    Many thanks sir. It’s A pcm 351. Supra. I think 1990.
Results 1 to 25 of 27
Page 1 of 2 1 2