Hi Larry,
Thanks so much for the clarification, I really appreciate it!
It turned out to be a bad fuel pump which is sort of a bummer because I just had it replaced 18 months ago.
Down here in...
Type: Posts; User: rkmfl
Hi Larry,
Thanks so much for the clarification, I really appreciate it!
It turned out to be a bad fuel pump which is sort of a bummer because I just had it replaced 18 months ago.
Down here in...
My post may have been confusing .. To state another way...
Can anyone with an Assault 325 that uses the MEFI 4-B (I think this was 2004 to 2007 or so, possibly?) -- tell me whether the sensor just...
Hi all,
We've had our 2005 Supra Launch 21v off the water for 6 months due to a busy period of work.
We're in West Palm so we don't winterize and it's only been stored during warm months.
...
@jzelt -
I'm really sorry I didn't see your post earlier. I'm going to reply on the assumption that this information might help someone else, even if it's too late to help you.
I had problems...
I'm having my 2005 Launch 21V re-upholstered. One thing I noticed about the 2005 upholstery versus the more recent upholstery (2008 and later, I believe, but not sure of the exact period where they...
That's not a huge amount of ballast, therefore, the ACME #1235 should be a little more than he needs, unless he's at a high altitude.
The ACME #1433 is probably a better fit.
More directly to...
Eric, I'm sorry that I don't have a specific answer to your question, but I thought I would share some information I learned on the topic.
First, I had done a little searching on Google back when...
@Beast - I contacted Rinda and purchased their cheap flasher. They explained this will not reset the codes, but at least I'll know if/when codes are being thrown.
For anyone else stumbling on...
Okay, from what you're saying, the original owner must have upgraded because my swivel only has a single pin that drops down into one of three holes.
If I understand you correctly, the old...
@wotan2525 - Thank you for the ECU table. Unfortunately those part numbers don't relate to the part number I have on the Indmar ECU. However, your idea did inspire me to write the ECU number down...
@Sluggo - Those are great images, thank you!
The only thing I did not understand, is the difference between the original (single pin that drops into place with gravity) versus the newest model...
I have a 2005 Supra Launch 21V with the upgraded 340 motor (ETX headers).
Every now and then the motor will set itself to run in protective mode, for things as simple as the battery being...
@Sluggo,
I also have a 2005 Supra that I had purchased used, and the wakeboard pivots use a single pin that drops-in from the top.
Based on what you posted, it sounds like this may be the newer...
About the three iterations with the hard-cut compound, that's not intended to be a "hard" number.
Rather it's expressing that because even hard-cut compound is relatively light, and gelcoat is...
I have a torn section of carpet on my Supra 2005 Launch 21V. I'm going to have my upholstery guy attempt to match this perfectly, and replace that section alone.
Does anyone know which brand of...
Although this project is complete, I'll post some things I learned over @ AutoGeeks.net, which is sort of the definitive site for a lot of detailers:
First, for your random orbital, the best...
My direct-drive boat (which I have not yet sold) is a Moomba and I've been a long-time member of the forum. My Supra Launch is my new upgrade.
I was only referring to the coupon code they have,...
DOCDRS - This is excellent information, thank you. I've probably spent an hour on the Moomba forum after you mentioned it, there is a lot of great information over there on ballasts.
I'm going to...
First, to DOCDRS - based on the other posts, it sounds like you have a 3x JABSCO system, is that correct? Are you running these on relays like Jaime mentioned? If not, have you found something...
Jamie,
In my reply, I was agreeing with your post and I believe I've stated all of your points in my positive-v-negative summary.
The #2 link you sent appears to go to:...
Okay, so it sounds like the pumps are very loud in that case. This is good to know, thank you.
How do you think the new systems determine the percentage the ballasts have filled? For example,...
I can't thank you guys enough for the heads-up as well as the assist on this.
I'm calling Indmar first thing tomorrow and ordering the parts/instructions.
Once I get them I'll scan/post here,...
This is truly excellent information so far, thank you. In reply:
To reply regarding: Your suggestion of using an aereator pump (eg TSUNAMI 1200) for improved filling speed, versus the heavy-duty...
I probably read a dozen posts on ballast upgrades in the forums, but I haven't read much on the 3-pump upgrade process specifically (using the 3 reversible vein pumps).
I've spoken with Jason @...
Kjkimball & Docdrs - thanks a lot for this!
Is this something I can retrofit by removing the assembly and drilling a hole somewhere, or do I need to buy a new pump assembly? If the only option...