Search:

Type: Posts; User: Jetlink

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    244

    I had a similar issue with my Comp. I ended up...

    I had a similar issue with my Comp. I ended up installing an expansion chamber in the vent line and the problem has pretty much disappeared.
  2. Replies
    1
    Views
    191

    Start and hopefully end your search...

    Start and hopefully end your search here.https://www.greatlakesskipper.com/search/?q=Access
  3. Replies
    9
    Views
    8,768

    Personally I look at it like this. I do not like...

    Personally I look at it like this. I do not like to work harder than I must. Same thing with engines. Why run a smaller engine really hard when a slightly larger engine does the same work but with...
  4. Out of curiosity, where in northern illinois are...

    Out of curiosity, where in northern illinois are you and who was the person you bought it from?
  5. Replies
    57
    Views
    24,112

    That is the second Comp I have seen with a teak...

    That is the second Comp I have seen with a teak platform.
  6. Replies
    110
    Views
    13,110

    No Wake is what all slalom skiers aspire to both...

    No Wake is what all slalom skiers aspire to both boat wake and skiing form. Two posts up is a perfect example.
  7. Letís be honest here, Mischief IV is going to be...

    Letís be honest here, Mischief IV is going to be more new than original at this point in time so I donít think itís really an almost 40 year old boat at his point. Itís only 40 on paper.
  8. Replies
    57
    Views
    24,112

    Speakers? Just open the throttle, get up on plane...

    Speakers? Just open the throttle, get up on plane and let that 351W sing the song of my people for everyone on the lake.
  9. Replies
    13
    Views
    2,334

    All correct however, adjusting the plate up might...

    All correct however, adjusting the plate up might move the high bump in the wake closer to the transom for you.
  10. Replies
    13
    Views
    2,334

    Even if it is not truly adjustable, if you can...

    Even if it is not truly adjustable, if you can tweak it a bit to remove any down deflection or stern lifting action might help before trying to remove the plate for a swap.
  11. Replies
    13
    Views
    2,334

    There are two thoughts here. First being to add a...

    There are two thoughts here. First being to add a little weight to the port side of the boat to level/even out the list to starboard that is resulting in a slightly asymmetrical convergence of the...
  12. Replies
    122
    Views
    45,024

    Yeah, "little kid" cannot stop talking about TN...

    Yeah, "little kid" cannot stop talking about TN and GA and wants to go back. Secretly I think she wants us to get a place or move there but that is another discussion. As for surfing I think everyone...
  13. Replies
    13
    Views
    2,334

    Can you post a picture or video of your wake? To...

    Can you post a picture or video of your wake? To answer your question, adjusting the plate properly should help flatten or tamp that down.
  14. Replies
    6
    Views
    3,471

    I doubt it is truly a Comp. Looks like it is the...

    I doubt it is truly a Comp. Looks like it is the water scooping model aka the Conbrio.
  15. Replies
    14
    Views
    8,359

    He's right, do not waste your time with these.

    He's right, do not waste your time with these.
  16. Replies
    17
    Views
    9,817

    For the oil drain, most boats usually have a...

    For the oil drain, most boats usually have a "remote" drain line that will go from a low point in the pan, basically where the plug would be and then have a section of line that runs long enough to...
  17. Replies
    81
    Views
    85,010

    That is more to keep the transom down as most...

    That is more to keep the transom down as most Comps do not have transom tie downs like other boats and trailers.
  18. Replies
    1
    Views
    11,052

    If you get it, first thing to do is ditch that...

    If you get it, first thing to do is ditch that stainless steel prop and get a proper CNC brass one on there instead.
  19. This advice brought to you by the law offices of...

    This advice brought to you by the law offices of Mischief IV, MJHKnox and Associates.
  20. Replies
    3
    Views
    9,002

    Thanks, I nearly spit out my drink reading that.

    Thanks, I nearly spit out my drink reading that.
  21. Well this escalated quickly.

    Well this escalated quickly.
  22. Replies
    4
    Views
    3,840

    I replaced the rudder on my Comp beginning of the...

    I replaced the rudder on my Comp beginning of the season as the seals were toast and you cannot get parts for it anymore. Ordered this and have had zero issues since install....
  23. Replies
    5
    Views
    8,435

    Wish I could say that this is a shock to me but...

    Wish I could say that this is a shock to me but alas, these older boats are getting harder to get parts for. I will stop in at my dealer tomorrow and see if they can reference the part for you.
  24. Replies
    10
    Views
    7,334

    Iíll save you the math, the two of you are about...

    Iíll save you the math, the two of you are about 8-9 hours driving one way between you depending on where in southeast Michigan you are.
  25. Replies
    5
    Views
    8,435

    What year Comp? I was able to get an all...

    What year Comp? I was able to get an all composite/plastic drivers seat shell from Skiers Choice, ordered through my local Supra dealer about 5 years ago. I had it covered and everything and the best...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4