The Arco 70200 is what I ended up with and it works great. Got it from a different site, as skidim wanted nearly $50 more for it.
Sent from my SM-G955U using Tapatalk
Type: Posts; User: PBWolf
The Arco 70200 is what I ended up with and it works great. Got it from a different site, as skidim wanted nearly $50 more for it.
Sent from my SM-G955U using Tapatalk
Mine does that as well, was worried about it but I read some other forums, and the consensus was 2 things, the first being what scottschmitt said about the rudder offset, and the second had to do...
Holy crap! It's my exact boat, 45 minutes from home..
https://huntsville.craigslist.org/boa/6179096821.html
Hey man I can pm you my email if you'll send me a copy. Those look nice and I can have a local guy print them for me.
Sent from my SM-G955U using Tapatalk
Well now I'm second guessing my choice.. I am positive my engine is LH rotation based on the engine serial number... but now looking again at that arco diagram, for LH engine you need CW starter in...
Yeah that's the RH (clockwise rotation) version. Hope that's what you need. 70201 is the standard (LH/CCW) version, hope that's what I need, too, because I want to be on the water this weekend.
...
Curious what starter you guys are running in your Supra's with the 351w.. Mine crapped out - probably due to old age and also getting a bit wet the last season or two (I had a leaky shaft seal and...
I just pulled new hose from the blowers to the transom vents in my 96 La Brisa. Not sure if you have the same routing, but 10ft per side should be plenty, even with having to bunch it up in the...
Oops! Disregard my statement then..
Not the impeller itself, but the entire pump can be put on upside down so that the inflow hose is now hooked up to the outflow. Only an issue if you actually took off the entire pump, not just...
So, emptied and started to take out the gas tank but was able to avoid fully removing it by having my wife assist me.. her slender arms were able to fit through the exhaust ports on the back down...
Stuffing in shaft seal is the primary culprit as others have said.. a few drips a minute is normal. If it's an older boat, the exhaust flanges (or whatever they are called) where they exit thru the...
I'm replacing most of mine as well. In my 96 La Brisa, the hose feeding fresh air into the bilge at the front is 4". The hose on the blower to the back exhaust vents is 3". I don't think there...
I have the same issue on my 96 La Brisa... the Lowrance gauge was all cracked and messed up.. I got it out and took it apart and it appears to have gotten water inside it. I've read that since the...
This is the only one I have, under the floor beneath the back seat. The hose, as it travels to the stern, disintegrates into nothing under the gas tank. I can see others hanging back there but...
Im an idiot.. I found where the front vents go... but want to make sure Im only supposed to have one blower/hose feeding whatever setup is behind the gas tank for the stern vents.
Sent from my...
So I recently noticed that my bilge vent hose has pretty much deteriorated into nothing at the stern. My blower motor was also just resting next to the exhaust hose, not mounted at all. The...
My La Brisa sat out in the weather quite a bit before I got it. The "UV coating" on the tower speakers was yellow and cracking/peeling, totally gone in some places. I wanted to refinish them, as...
Today I replaced a two wire bilge pump with a 3-wire one...
I had two bilge switches on the dash, "Bilge 1" was wired to the pump originally.. "Bilge 2" led me to believe I had second pump but...
Sadly that's one of the numbers that put me on the chase for the wrong seal. I actually had NOK AD2527E stamped on the rubber of mine, but that pulled up the SAME wrong seal. They are all .3 in...
Well, that was a couple of days of hell trying to get the right parts for my hubs.. Had the correct bearings and races, but I couldn't find the proper grease seal to save my life. I needed a...
Couple of older Tennessee Valley/North Alabama finds:
Comp: http://huntsville.craigslist.org/boa/5558758941.html
Unknown (saltare? beast?): http://huntsville.craigslist.org/bod/5594227510.html
Phew, I wasn't aware a new trailer would be that pricey.
In any case, I already got to work on the spindle.. had a friend that is more knowledgeable than I come over and supervise.. We re-cut...
So, long story short I blew a bearing on the original trailer my 1996 La Brisa came with (at least, I think it was the OEM trailer). It was in pretty rough shape already but now after this damage...
Hey, I didn't get to go - but I got my shirt from Ben and wore it with pride this past weekend or two at the lake!
http://i.imgur.com/PwD0kiqh.jpg