Search:

Type: Posts; User: carlossa

Page 1 of 3 1 2 3

Search: Search took 0.02 seconds.

  1. Pierburg and bosch reg replacement "New System"

    Ok Supra gang, to cut a long story short, years ago I put an 06 MEFI 5 320 MPI Indmar from a Malibu into my 04 SSV Launch. I purchased the complete engine less fuel pump bracket that has the bosch...
  2. Replies
    17
    Views
    55,645

    Nice concept. I went full custom and made one...

    Nice concept. I went full custom and made one similar to the new style. The stainless grab rail is deadly to the feet in my opinion. After getting my foot caught in it jumping into the water a few...
  3. Replies
    46
    Views
    76,791

    I love this thread. One mans search for his...

    I love this thread. One mans search for his ultimate vessel that he once owned. Good luck with the search and I'll watch with interest. Oh, and If I ever see one down under, I'll let you know.
  4. Hows the oil level? Check your linkages are...

    Hows the oil level? Check your linkages are moving. Mine blew the front seal out and dumped the lot (oil) into the bilge. ZF trannys are pretty good. not much to them.
  5. Replies
    1
    Views
    1,022

    There should be two cables, one for gear...

    There should be two cables, one for gear selection and one for throttle. Id say your throttle end may have come off the engine end or hand end or could be cactus. If its drive by wire, the plug in...
  6. Replies
    2
    Views
    1,311

    That Model tower is probably a "new dimensions"...

    That Model tower is probably a "new dimensions" tower. I would love new racks also. I have found some in the US but it is not economical for me to ship from seller. If you find extras at a reasonable...
  7. Replies
    6
    Views
    1,771

    Thanks Coose :D

    Thanks Coose :D
  8. Replies
    6
    Views
    1,771

    You may need to machine it out failing the wire...

    You may need to machine it out failing the wire brush method. On another note, can you mention the seal Part no. or sizes when you replace it. I need to do mine and could do with a head start.
  9. Replies
    12
    Views
    3,608

    Yep. Wedding band. Wife wasn't overly upset as we...

    Yep. Wedding band. Wife wasn't overly upset as we were doing something we both love........watersking. It did help the situation the fact that she was present when it happened.;)
  10. Replies
    15
    Views
    5,518

    Could also be the camshaft welsh plug. Its been a...

    Could also be the camshaft welsh plug. Its been a while since I pulled a windsor apart, but chevs definately have them. They do tend to rust out and you will lose masses of oil.
  11. Replies
    4
    Views
    1,407

    179421794017941 22" long oval extrusion is 1"...

    179421794017941

    22" long oval extrusion is 1" wide 1 7/8" high, has a 1/8" wall thickness and is bent 7 degrees right in the middle.
    Regards Carl
  12. Replies
    4
    Views
    1,407

    Hi Rickard They do have a slight bend in them....

    Hi Rickard
    They do have a slight bend in them. maybe 5-10 degrees. Ill get a phot when I return home from work. Its 5 am downunder ATM.
    Regards Carl
  13. Replies
    14
    Views
    8,370

    Hi Shaun Yes, the input shaft into the trans. If...

    Hi Shaun
    Yes, the input shaft into the trans. If it lets go all your oil is pumped straight out into the bilge and all drive is lost.
    Carl
  14. Replies
    14
    Views
    8,370

    Hi Shaun I did a similar swap. Put a 06 Malibu...

    Hi Shaun
    I did a similar swap. Put a 06 Malibu 320LCR in my 04 Launch SSV. I have attached a pic of the mounts. I'm not sure if 08 are the same but 07 definately are.I re-machined everything in...
  15. Replies
    22
    Views
    7,764

    Yes Mark, Just a plain old bit of wood. No...

    Yes Mark, Just a plain old bit of wood. No bindings and no fin, but a heap of fun.
    Carl
  16. Replies
    22
    Views
    7,764

    Nice and hot downunder at the moment. 95F - 100F...

    Nice and hot downunder at the moment. 95F - 100F
    17926
  17. Well done Ned. The best part is.......look how...

    Well done Ned. The best part is.......look how much you've learnt. Looks like you'll be hitting the water this weekend,
  18. Ned, Just ran an eye over mine and remembered...

    Ned,
    Just ran an eye over mine and remembered that the ecm sould have a separate earth on it. Mine bolts to the bellhousing close to the main earth lead. Might be worth changing the wire to a new...
  19. Ned Have you cleaned the corrosion out of the...

    Ned
    Have you cleaned the corrosion out of the inside of the dizzy cap? I'm kind of leaning toward an earthing fault. I'll have a good look over mine today and see what I find.
    Regards Carl
  20. Hey Ned I've been down a similar road and it...

    Hey Ned
    I've been down a similar road and it turned out to be fuel pressure related. MEFI 5 is very fussy, if you get a +/- 5-8 psi variance of fuel pressure it can frustrate the hell out of you. I...
  21. Replies
    12
    Views
    3,939

    Another trick I use if you dont have access to a...

    Another trick I use if you dont have access to a flame is boiling water on the prop. Sometimes its that little bit of expansion that helps break the taper grip.
  22. Replies
    6
    Views
    2,046

    Try searching Google for "Aluminium Extrusion...

    Try searching Google for "Aluminium Extrusion Catalogue" and sort through the pages. I found this fairly quickly...
  23. Gogger The bolts within the inspection plate do...

    Gogger
    The bolts within the inspection plate do not need to come off. The trans and V drive have a splined connection. Once you get all the v-drive bolts undone (6 I think) it should jiggle forward...
  24. How is the progress going Gogger?

    How is the progress going Gogger?
  25. Replies
    22
    Views
    8,141

    16657 although your season is ending, ours is...

    16657 although your season is ending, ours is just beginning

    Sent from my SM-G900I using Tapatalk
Results 1 to 25 of 61
Page 1 of 3 1 2 3