Search:

Type: Posts; User: h2o-ski

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    27

    There could be a number of different locations...

    There could be a number of different locations that water could be leaking. While it could be the shaft packing, it could also be leaking exhaust, rudder port or leaking water hose.

    Best bet is...
  2. Replies
    3
    Views
    47

    I would check Acme propeller as they have a prop...

    I would check Acme propeller as they have a prop selector tool that will help find the prop based on the parameters you give it. Or I have heard that OJ props has great customer support. Also...
  3. Replies
    39
    Views
    29,002

    Work continues. Got the flooring faired and just...

    Work continues. Got the flooring faired and just have to sand a few spots smooth. I got the bilge and pylon holes cut. With all this recent progress I feel like I am actually working on a boat and...
  4. Replies
    3
    Views
    47

    A Borg Warner Velvet Drive 71c would have been...

    A Borg Warner Velvet Drive 71c would have been the transmission used. What prop are you using? It would be much cheaper to put a lower pitched prop on than trans and prop.
  5. Replies
    39
    Views
    29,002

    With the kids of on summer break, I've been able...

    With the kids of on summer break, I've been able to put some serious work done.

    The deck has had the corners rounded over and a coat of resin on all sides. I also got the battery access cut. Not...
  6. Replies
    39
    Views
    29,002

    I put the cap on one last time to make sure...

    I put the cap on one last time to make sure everything is at the correct height. For the most part it is dead on. There in only one area where I need to shim the floor up 1/8".

    I was able to...
  7. Replies
    3
    Views
    307

    I personally would not unless you are ready for...

    I personally would not unless you are ready for an extensive project or you have been waiting for that boat model. From the description it is a complete gut job and rebuild much like what I am in...
  8. Replies
    39
    Views
    29,002

    Status update: 3/4" BCX plywood hurt the...

    Status update: 3/4" BCX plywood hurt the pocketbook at $70 a sheet, but progress must continue. 90% of the flooring has been cut to size. I just have the area under the helmet to cut.

    I took...
  9. Replies
    39
    Views
    29,002

    Progress is picking up. I cut up my old pylon...

    Progress is picking up. I cut up my old pylon assembly to free the original pylon and also to use the sides for backers for the new assembly. I also picked up most of the plywood flooring and...
  10. Replies
    39
    Views
    29,002

    Progress has been slow but still making it. I got...

    Progress has been slow but still making it. I got the exhaust hose in and setup.

    A family event put me in the general area of the legendary Mischief. So it was decided we should perform a...
  11. Replies
    39
    Views
    29,002

    Well onto set back #164 (exaggerating but not by...

    Well onto set back #164 (exaggerating but not by much). I noticed that the base for the pylon was still flaking off after I got it to bare metal before I painted it. After further inspection, I'm...
  12. Replies
    39
    Views
    29,002

    Here are some pictures of the cap repair. There...

    Here are some pictures of the cap repair. There was far more repair work on where the cap and the storage locker meet but due to how I have the cap supported I can't get a good picture of it.
    ...
  13. Replies
    39
    Views
    29,002

    The floor that I pulled out was 3/4" marine ply. ...

    The floor that I pulled out was 3/4" marine ply. My uncle replaced the floors after he got it because they rotted out back then. The cap has been back on the hull 3 times to make sure there is room...
  14. Replies
    39
    Views
    29,002

    Progress report Built bulkheads to help prevent...

    Progress report
    Built bulkheads to help prevent water intrusion and support the floor. I have 3/4" flooring planned.
    I placed the cap on one more time and everything looks to be close. So far the...
  15. Thread: 87 Ts6m Parts

    by h2o-ski
    Replies
    6
    Views
    2,648

    Thank you for the bolt spacing. I will measure...

    Thank you for the bolt spacing. I will measure shortly and get back with you
  16. Thread: 87 Ts6m Parts

    by h2o-ski
    Replies
    6
    Views
    2,648

    I figured that was what you were talking about. ...

    I figured that was what you were talking about. To see if I can retrofit that bracket to my '81, would you be able to tell me the bolt spacing, unless prop struts are a standard bolt pattern. Also...
  17. Thread: 87 Ts6m Parts

    by h2o-ski
    Replies
    6
    Views
    2,648

    Just out of curiosity what steering bracket are...

    Just out of curiosity what steering bracket are you selling?
  18. Replies
    5
    Views
    3,210

    I have been eyeing those but I just can't see...

    I have been eyeing those but I just can't see spending that money on exhaust tips. I'm looking for more budget friendly alternatives.
  19. Replies
    14
    Views
    8,185

    Bummer those would not work. My new transom and...

    Bummer those would not work. My new transom and stringers say thank you.
  20. Replies
    14
    Views
    8,185

    By chance do you have the exhaust through hulls...

    By chance do you have the exhaust through hulls or exhaust tips? I need a 3" id tip to replace the poor setup on mine

    Sent from my SM-G950U using Tapatalk
  21. Replies
    5
    Views
    3,210

    ISO Exhaust Tips

    I was wondering if anyone had any 3" ID exhaust tips that I could take off someone's hands.

    My '81 just had 3" fiberglass tube siliconed in place with flappers clamped on. I am in search of...
  22. Replies
    39
    Views
    29,002

    Test Fit

    Time for an update. This past weekend I rebuilt the gantry cranes and got the repaired cap (she is not going to win any beauty pageants) back up in the air. Boy were my measurements wrong in the...
  23. Replies
    18
    Views
    13,214

    Thank you for the pictures of an actual Sport. ...

    Thank you for the pictures of an actual Sport. There are quite a few subtle differences between the 81 and 82 Sports.
  24. Replies
    39
    Views
    29,002

    Thank you for feedback and the confidence boost. ...

    Thank you for feedback and the confidence boost. Fiberglassing in the Texas heat really does wear down on ya. I went and confirmed that there is about 1/4" lip that allows for even more leeway. ...
  25. Replies
    39
    Views
    29,002

    Happy birthday to "The Money Pit"! Turning 40...

    Happy birthday to "The Money Pit"! Turning 40 sometime this month if not already.

    Too bad it is still under rebuild to take a lap around the lake.

    Sent from my SM-G950U using Tapatalk
Results 1 to 25 of 38
Page 1 of 2 1 2