Search:

I would put the D.U.I distributor in and call it a day. I fought my electronic Mallory ignition for a little while. The coils kept overheating and having problems. The boat would miss when the coil...

Still trying to figure this thing out.
So I bought a new coil and ballast resister from Napa Auto parts. The lady at the counter didn't know what ballast resister went with the coil.
The coil I...

Let me know if all of those people fall through. I have a vinyl cutter and can throw some together for you. Are you looking for the supra waves, the whole lines down the boat, or something a little...

Bump to the top

here are some links to images of the coil and the resistor. couldn't figure out how to link them so they came up in the thread.
the purple wire comes out of the distributor and goes to positive...

I have not tried recreational fuel, actually i have never heard of it.

Yes it is a external mounted coil. It is the one that skidim sells it says " 12V use with external resistor 903"

The resistor is externally mounted at the back of the engine and it has a circle...

Carb is brand new last season from skidim. Carb seems to run and function fine.... Had this same issue with the last carb except the old one would puke fuel .

I have a 1988 Supra Comp TS6M with the 351 Windsor.
It will run fine for 15 - 20 min through our no wake zone and when we get out on to the main lake we run around at 25 - 30 mph for 10 minutes or...

I had my heater core leak and it would fill up under the drivers floor board and then run to the back by the exhaust tube. Your could be going the other way and down the passenger side. Check the...

Stick with old faithful.
http://www.skidim.com/mobile/4160-CARBURETOR-4V-GM-350_FORD-351/productinfo/RA052003/

Trade me for my TS6M :)

When you hit the switch does the light on the dash come on?
Is it getting power?

Is there any coil that you can pick up from napa / autozone / oreilly that will work?
My coil is the same as the one on skidim R117001and it has the prestolite electronic conversion without a...

Heard you might be getting some rain again. Stay Safe.

I think I found the leak. I'm still guessing it was (is) the heater core up front. I think it was leaking and dripping into the carpet and gravity led it towards the foot rest tray area where the...

Motor mounts "seem" solid. You can torque down on them and it bites into the wood. Same with the transmission mounts and the gas tank straps. Everything has been sealed with some sort of caulking or...

Thanks 2500 I will check that when I get home.

Jetlink, I had a sneaky suspicion that was the case. I'm just really surprised by the amount of water in the boat with what seems like no rot...

I did check the bilge hose when I was under there and saw it. I laughed cause it would have been funny If it was that easy. But it's me and nothing could be that simple. Going to take it back to the...

So it doesn't seem to be leaking from the heater. Might go get 5/8 heater hose plugs and just plug it anyway.
Under the drivers feet is where there is quite a bit of water. When I push on the floor...

Ok, so digging deeper. The boat has a heater in the bow, maybe that is leaking. Time to climb under and check it out

I think the water that was spritzing was just the water that was trapped and the vibrations making it do that. It never really got higher.

Still curious about the bow foam and maybe that it's...

Here is video of it on the launch ramp at a pretty steep angle. Sucking water from the lake and the boat submerged. Didn't see anywhere at the rear where it could be leaking and coming in. At the end...

So here is a video of the boat in the driveway running with the raw water put into a bucket. Doesn't seem like anything is leaking that I could see.

https://youtu.be/7L_TzxT7uLI

What kind of resin did you use for it?