Search:

Type: Posts; User: michael hunter

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    53

    Check the exhaust manifolds also.

    Check the exhaust manifolds also.
  2. If the knock sensor is not securely connected it...

    If the knock sensor is not securely connected it will throw a code and may affect driveability.
  3. Yes it looks like a plug for the engine block....

    Yes it looks like a plug for the engine block. Look on the sides below the exhaust manifolds or add water and look for the leak. The stud and nut is to hold the Knock sensor . Look on the engine...
  4. Replies
    8
    Views
    229

    Don't throw the pan away . They are not available...

    Don't throw the pan away . They are not available anymore.
  5. Replies
    5
    Views
    125

    The injectors get their signal from the ignition...

    The injectors get their signal from the ignition primary through the ECM . It sounds like the ECM may be the problem . You don't have the equipment to test it . You may want to talk to the dealer at...
  6. Of the two boats you show the 96 is a full...

    Of the two boats you show the 96 is a full composite built boat where as the 89 is a wood stringer boat . It will probably need a full stringer job unless it's already been done. As for making a wake...
  7. Replies
    10
    Views
    278

    I have a PCM # RP173072 electronic ignition...

    I have a PCM # RP173072 electronic ignition conversion kit new in the box . I don't know if its made by petronix. I use HEI distributors in my 351 engines single wire hook up 60,000 volts to the...
  8. This is for a 1989 .What year is yours? ...

    This is for a 1989 .What year is yours?

    https://i.imgur.com/wXltNUn.jpg?6
  9. Replies
    8
    Views
    229

    You will need to post pics . I don't follow what...

    You will need to post pics . I don't follow what you are talking about?
  10. That might work if the stringers are dry ? They...

    That might work if the stringers are dry ? They are usually saturated with water. As Mischiel said what do you have to loose?
  11. Replies
    8
    Views
    229

    The last pan I installed I didn't put the hole in...

    The last pan I installed I didn't put the hole in it at all . It just dumps the water on the back side of the stringer. If you are a good driver you shouldn't get water there . If you do a towel...
  12. Replies
    5
    Views
    141

    +1 on what jetlink said. You need to suck the...

    +1 on what jetlink said. You need to suck the trans fluid out the dipstick hole with a 1/4'' plastic hose. Be careful some have gotten the hose stuck in the trans . I have been doing this for 30...
  13. Replies
    5
    Views
    141

    Marine mechanics are very expensive and rarely do...

    Marine mechanics are very expensive and rarely do work that up to par with the bill. Your best bet is to educate yourself and do your own maintenance. Your Comp is one of the simplest boat to work...
  14. That might work if there is anything for the...

    That might work if there is anything for the epoxy to adhere to. Definitely worth a try. That is a big boat to do the stringers and floor correctly it will need to have the top cap removed. BIG job...
  15. Replies
    7
    Views
    207

    Yes and maybe drill a couple new holes and add...

    Yes and maybe drill a couple new holes and add screws into a new location.
  16. Replies
    10
    Views
    278

    That is called a dirty neutral. It is most likely...

    That is called a dirty neutral. It is most likely because the clutches inside the trans are warped from excessive heat . There are a lot of transmissions with that problem . It will work for a long...
  17. Replies
    10
    Views
    278

    Does it have points or electronic ignition? Where...

    Does it have points or electronic ignition? Where are you located?
  18. Replies
    6
    Views
    294

    Outstanding work you are truly an engineer.

    Outstanding work you are truly an engineer.
  19. Replies
    1
    Views
    209

    Sounds like the switch . you can run a jumper...

    Sounds like the switch . you can run a jumper wire to confirm.
  20. I have a set off a comp . I will have to check...

    I have a set off a comp . I will have to check size for you.
  21. Replies
    4
    Views
    219

    Mobil 1 15W50 is recommended by Mobil in all flat...

    Mobil 1 15W50 is recommended by Mobil in all flat tappet and roller lifter engines . It is available at Walmart $ 22-26 for 5 qts . As for filters any will do except Fram orange . I use Motorcraft...
  22. Replies
    1
    Views
    118

    I just buy 2'' pipe insulation my wife makes the...

    I just buy 2'' pipe insulation my wife makes the covers
  23. Replies
    7
    Views
    294

    The water around the prop is from the dripless...

    The water around the prop is from the dripless coupler around the propshaft. It has a hose going to it to cool and lubricate it. Its normal fir water to come out when running out of water. I don't...
  24. Replies
    7
    Views
    636

    I have a boat with GPS zero off and a 92 comp...

    I have a boat with GPS zero off and a 92 comp without . Although it does make it easier on the driver it would not be worth it to me.
  25. Replies
    3
    Views
    228

    Yes the control splits in half after removing the...

    Yes the control splits in half after removing the 1/4'' bolts from the inside. You will need to remove the shift arms take note of their position. In the pic I have a screwdriver pointing at one of...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4