Search:

Type: Posts; User: michael hunter

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    11
    Views
    269

    If the input shaft on the trans is spinning and...

    If the input shaft on the trans is spinning and the output is not check the drive shaft cuppler if its ok the trans has an internal problem . Its a 1 to 1 gear ratio.
  2. Replies
    11
    Views
    269

    It sounds like the damper plate may be broken it...

    It sounds like the damper plate may be broken it is the connection between the engine flywheel and the transmission input shaft kinda like a clutch on a car . If the damper is broken its a easy...
  3. Replies
    3
    Views
    95

    First when you shut down the engine when...

    First when you shut down the engine when overheated it probably pulled water into the cylinders and hydro locked the engine. When you tried to start it you killed the starter. Hopefully the rods are...
  4. Replies
    11
    Views
    269

    Pull the trans and make sure the damper plate is...

    Pull the trans and make sure the damper plate is turning the input shaft . If that is it its an easy fix .
  5. www.uscomposites.com is a good source of...

    www.uscomposites.com is a good source of materials and advice. After cleaning and grinding the stringer locations on the hull I put a coat of CPES [clear penetrating epoxy sealer] from...
  6. Could be ignition also are you still running...

    Could be ignition also are you still running points?
  7. +1 looks like freeze damage to me ? Any water in...

    +1 looks like freeze damage to me ? Any water in the oil?
  8. Replies
    2
    Views
    146

    Check the fuel pressure.

    Check the fuel pressure.
  9. Replies
    2
    Views
    122

    Looks like a 5.7 L GM engine.

    Looks like a 5.7 L GM engine.
  10. Much better

    Much better
  11. Possibly the worst set of pictures I have ever...

    Possibly the worst set of pictures I have ever seen ? Why don't you try and post some of the top side of the boat?
  12. Replies
    4
    Views
    272

    Try a suck gate first you can make one for about...

    Try a suck gate first you can make one for about $20.00.
  13. Replies
    8
    Views
    355

    I don't think 1/8'' aluminum will hold a 351...

    I don't think 1/8'' aluminum will hold a 351 engine and trans. The only inboard boat that uses aluminum I know of is Pavati . I would use Douglas Fur and lots of CPES . It will not require completely...
  14. Replies
    11
    Views
    484

    Are you sure its not the prop shaft packing? They...

    Are you sure its not the prop shaft packing? They are supposed to leak a few drops per minute to lubricate the packing.
  15. Replies
    2
    Views
    157

    Check the rudder port.

    Check the rudder port.
  16. Replies
    5
    Views
    270

    If the starter solenoid is clicking then its not...

    If the starter solenoid is clicking then its not the neutral safety switch on the trans. Check the battery and the main battery wires at both the battery and the engine ground and the solenoid . Then...
  17. Replies
    5
    Views
    270

    The button on the throttle control has nothing to...

    The button on the throttle control has nothing to do with the starter . The neutral safety switch is on the top of the transmission . It sounds like the shift cable is out of adjustment.
  18. Replies
    6
    Views
    330

    Why are you changing the stock design ?

    Why are you changing the stock design ?
  19. Sounds like you may be in need of a carb...

    Sounds like you may be in need of a carb overhaul. Did you replace the points ? Open the gap manually and look if they are burned replace them.
  20. I don't remember just look at the starter if the...

    I don't remember just look at the starter if the relay is on the starter then yes.
  21. Replies
    3
    Views
    215

    Mine is a 89 i'm not sure its the same as yours a...

    Mine is a 89 i'm not sure its the same as yours a pic of your dash would help. The warning lights on the dash generally don't work the control box that runs them had all kinds of problems. I...
  22. If you are running points start there, As a rule...

    If you are running points start there, As a rule they should be replaced every year or so. At minimum reset the point gap .The point gap for a Prestolite distributor is .018'' dwell is 29 to 33...
  23. You will have to check with Mallory on...

    You will have to check with Mallory on installation instructions. I like the DUI ignition system I have it on 3 of my 351w boats all run great.
  24. If you replace the relay you must get a high...

    If you replace the relay you must get a high quality heavy duty relay. The stuff sold at the big box auto parts stores are junk. I replaced the starters on two of my Supras with a gear reduction...
  25. That i term is usually not used with electronic...

    That i term is usually not used with electronic ignition . I am not familiar with the mallory set up . All of my boats are running DUI . If you have 3 dead cylinders you should start with a...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4