Search:

Type: Posts; User: Tonymozingo

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    8,716

    Tried 30 mins to figure out how to send a pic to...

    Tried 30 mins to figure out how to send a pic to no avail. I’ll report back later. Thanks for hanging in there with me.
  2. Replies
    10
    Views
    8,716

    Ok. Thanks. I’ll check both. Where is...

    Ok. Thanks. I’ll check both.
    Where is thermostat located?
  3. Replies
    10
    Views
    8,716

    351W PleasureCraft overheating...

    First, thanks to all who contributed advice as I rebuilt an Ď86 over the winter. It runs well. However, I have a new problem.
    The engine overheats soon after cranking. I replaced the impeller and...
  4. Replies
    2
    Views
    336

    Please help me

    Please help me
  5. Replies
    2
    Views
    336

    351 PC Windsor Wiring question

    I’ve installed new carb, new distributor, fuel line, filter and pump, plug wires, plugs, and wiring harness. I think I have it wired up correctly and I have it 8 degrees before TDC. I have the rotor...
  6. Replies
    1
    Views
    423

    351 Windsor PC Distributor housing

    Trying to delete post
  7. Replies
    1
    Views
    291

    Setting Timing-351 Windsor PC

    Iíve received my new distributor and carb and am ready to attempt setting the timing. Iíd appreciate someone helping me or referring me to a site I can go to for learning how.
    Is there a tutorial...
  8. Replies
    5
    Views
    653

    I am so glad for this advice. There’s no sludge,...

    I am so glad for this advice. There’s no sludge, but whatever additive or ? The previous owner put in definitely broke down. The fuel has a peculiar smell and a reddish tint. I’d hate to know I ran...
  9. Replies
    5
    Views
    653

    Any tips on siphoning? I can’t get the...

    Any tips on siphoning? I can’t get the remainder; it’s still half full. Is there a certain shape of the tank preventing the hose from reaching deep enough?
  10. Replies
    5
    Views
    653

    Old gas; 351 PCM

    89 Supra has been on rack for ten years. Almost full of gasoline.
    Iím installing a new carb.
    Question: Is there a reasonably easy way to drain the old gas from the tank, and if not, what should I...
  11. I took your advice and ordered from Skidim. Great...

    I took your advice and ordered from Skidim. Great folks. New carb and distributor coming. Thanks again
  12. Maybe I should dismount and replace the one I...

    Maybe I should dismount and replace the one I bought
  13. You won’t believe this, but I threw the old one...

    You won’t believe this, but I threw the old one away.
    I am so ignorant to do that.
    Any other suggestions? I get what you said about the wires and manual choke
  14. Thanks, Michael. One last question and Iíll...

    Thanks, Michael.

    One last question and Iíll stop bothering.
    I bought a Holley carb to replace the old and when I mounted it, I noticed it did not have the two prongs for the pos and neg elect....
  15. Hattiesburg, MS

    Hattiesburg, MS
  16. Ď89 Supra Ford 351 Windsor Distributor

    Starting this thread because I need the info. ASAP.
    Thanks in advance.

    Iím replacing the distributor because it had points. Took the old one out already.
    What are the parts ID numbers for new...
  17. Yes. So I took the entire distributor out and am...

    Yes. So I took the entire distributor out and am looking to replace the old with new.
    Would you please advise where and how to order a new distributor and cap,etc?
    My OíReillyís guys canít find...
  18. Man, that must be it. The wire from the dist. cap...

    Man, that must be it. The wire from the dist. cap was melted onto the coil and half that bond looks burnt.
    I really appreciate it, sir.
  19. That’s it! Could that be the reason I’m not...

    That’s it! Could that be the reason I’m not getting spark to the plugs?
  20. Part Identification and assistance needed

    Hi, I have an Ď89 Supra 351
    PleasureCraft. Itís been sitting for many years. I have it turning over and have determined itís not firing.
    I suppose Iím correct in replacing the next part down the...
  21. Replies
    0
    Views
    280

    Wanted- Swim platform for 1998 Supra

    I want to buy a platform and brackets for my Supra. The original was white fiberglass or plastic.
  22. Replies
    7
    Views
    956

    Crystal, That’s is the same boat model and color...

    Crystal, That’s is the same boat model and color as mine.

    1989 Supra PleasureCraft 351

    I’m happy to report through the members of this forum, I’ve gotten it wired correctly. Thank you.
    ...
  23. Replies
    7
    Views
    956

    https://forum.supraboats.com/images/attach/bmp.gif

    https://forum.supraboats.com/images/attach/bmp.gif
  24. Replies
    7
    Views
    956

    Many thanks sir. Itís A pcm 351. Supra. I think...

    Many thanks sir. Itís A pcm 351. Supra. I think 1990.
  25. Replies
    7
    Views
    956

    Many thanks to you. Itís a PCM 351. I think...

    Many thanks to you.
    Itís a PCM 351. I think around 1990 Supra.
    Iím trying to figure out how to Attach pics
Results 1 to 25 of 26
Page 1 of 2 1 2