Search:

Type: Posts; User: 2500HD

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds; generated 32 minute(s) ago.

  1. Replies
    14
    Views
    14,433

    Sticky: https://www.youtube.com/watch?v=s2Yy4lHK5nA...

    https://www.youtube.com/watch?v=s2Yy4lHK5nA
    https://www.youtube.com/watch?v=bsT6BwNuxoo
  2. Replies
    14
    Views
    14,433

    Sticky: Mines still going strong, Love it!

    Mines still going strong, Love it!
  3. Replies
    22
    Views
    1,850

    Throttle position sensor.

    Throttle position sensor.
  4. Replies
    9
    Views
    748

    Just do 1/4 turn at a time. In theory you...

    Just do 1/4 turn at a time. In theory you shouldn't need a wrench but the facts are that you will need one. even if you need to replace the packing it's like most things. Easy to do but a pain to...
  5. Replies
    22
    Views
    1,850

    Throw away the mdc. Here is my thread, Same boat....

    Throw away the mdc. Here is my thread, Same boat.
    https://forum.supraboats.com/showthread.php?17208-medallion-mdc-1600-delete-and-head-questions
  6. Replies
    22
    Views
    1,850

    I would check your throttle position sensor. Also...

    I would check your throttle position sensor. Also install a fuel pressure gauge up by the intake and see what it reads when this happens. I'll bet the pump is fine but this is the only way to know...
  7. Thread: My new boat!

    by 2500HD
    Replies
    7
    Views
    1,837

    Gettin closer.

    Gettin closer.
  8. Replies
    14
    Views
    1,266

    you canrun your boat on land if you have a hose...

    you canrun your boat on land if you have a hose to wet down the strut and the shaft through hull.
  9. Thread: Santera cover

    by 2500HD
    Replies
    0
    Views
    310

    Santera cover

    Can anyone in Colorado recommend someone for a snap on cover?
  10. Replies
    23
    Views
    2,830

    Take your head to a shop and have them pressure...

    Take your head to a shop and have them pressure test them. This will tell you if you have a small crack or not.
  11. Thread: lenco trim tabs

    by 2500HD
    Replies
    8
    Views
    2,024

    agree with dutchman, the tabs lengthen the wave...

    agree with dutchman, the tabs lengthen the wave without the need for bow weight. my boat doesn't have a bow bag so all the weight is in the rear. Both 750's puts out a nice wave but add another 500...
  12. Thread: lenco trim tabs

    by 2500HD
    Replies
    8
    Views
    2,024

    Search is your friend...

    Search is your friend
    https://forum.supraboats.com/showthread.php?14955-DIY-Wake-shaper
    I think i started these on page 9
  13. Thread: MAP sensor

    by 2500HD
    Replies
    4
    Views
    739

    What lively said.

    What lively said.
  14. Replies
    20
    Views
    2,585

    http://www.rockauto.com/en/moreinfo.php?pk=1111766...

    http://www.rockauto.com/en/moreinfo.php?pk=1111766&cc=1432495&jsn=540
  15. Replies
    20
    Views
    2,585

    I would almost guarantee that the map sensor is...

    I would almost guarantee that the map sensor is bad or has a bad connection. I had a bad one on my 260z and it ran really rich and backfired. There is a way to check the power supply to it but i...
  16. Replies
    20
    Views
    2,585

    efi is easier to work on than you think. I put a...

    efi is easier to work on than you think. I put a 2004 4.1L in my 74 260z and the efi is awesome to work on, so easy.
    Were all the plugs that aren't firing on one side of the Block? If so then your...
  17. Replies
    8
    Views
    1,381

    My best guess without codes is the map sensor...

    My best guess without codes is the map sensor When they go out they tend to run really rich.
  18. Thread: Battery Setup

    by 2500HD
    Replies
    17
    Views
    3,337

    The blue sea is a perko switch. Just a different...

    The blue sea is a perko switch. Just a different manufacturer. And you didn't answer his question. I don't have a dual battery set up so I'm no help. Sorry
  19. Thread: DIY Wake shaper

    by 2500HD
    Replies
    112
    Views
    53,588

    I forgot to add that 5x9 was the most you needed...

    I forgot to add that 5x9 was the most you needed to get the gate to work. One other tip is to tie it to your tower with the tab side facing forward and use a clay bar to remove wax or lake slime from...
  20. Thread: DIY Wake shaper

    by 2500HD
    Replies
    112
    Views
    53,588

    With the size of your boat and the amount of...

    With the size of your boat and the amount of weight you can add i would just build a suck gate. we just built one for my buddies 05 xlv moomba and with both rear 1100 bags half full and his center...
  21. Replies
    62
    Views
    18,855

    For what it's worth, with my old saltare about...

    For what it's worth, with my old saltare about for years ago my gate was really shallow angle maybe 14 degrees. wake plate was up just a little from neutral. weight was even and about the same as...
  22. Replies
    4
    Views
    864

    Raise your platform or build a new one, it is...

    Raise your platform or build a new one, it is squashing your wave and the upforce on it is stripping out the screws.
  23. Replies
    4
    Views
    1,389

    New prop will only make the boat better it will...

    New prop will only make the boat better it will have 0 effect on wave. Even prop rotation has little effect on the wave. Its actually the scags under the boat that dictate which side of the,boat the...
  24. Replies
    13
    Views
    6,796

    left click a section then right click and select...

    left click a section then right click and select print
  25. Replies
    3
    Views
    618

    Yes, coils can fail immediately. Cheap enough to...

    Yes, coils can fail immediately. Cheap enough to replace. I also think some auto parts places can check them for you.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4