Under the metal panels is the fuel tank. My panels were not screwed down, but I believe they normally are.
I am interested in the cost of the deckadence product as well.
Side note,...
Type: Posts; User: pridekit
Under the metal panels is the fuel tank. My panels were not screwed down, but I believe they normally are.
I am interested in the cost of the deckadence product as well.
Side note,...
Always keep the teak :) If you want to change it, take it off and have something else made for it, but don't lose the natural teak. It's too expensive and hard to come by.
I just messaged them on Instagram to see if they would be at the Miami show (they won't :( ). The labor of removal would be something you would want to do yourself, it's just a matter of cutting out...
Unfortunately I bit the bullet and bought it direct from Rinda. It's definitely a really cool piece of software, and in someways I hope I don't have to use it very much. But, at least I have it if I...
Rinda tech's DIACOM.
Sent from my iPhone using Tapatalk
So I have a couple of questions.
1) what do y'all suggest for cleaning the vinyl on my 2006 Launch? It seems to have collected a little bit of mildew during the repairs, as well as a couple of...
I reset to 1 TDC, pulled the distributor out until I cleared the cam gear. I was off a little bit on my alignment so I turned the rotor clock wise a smidge, dropped the distributor in. The point on...
Well, I figured out what I did wrong :)
Here's where my rotor at 1
http://images.tapatalk-cdn.com/16/01/02/6cabd6899b9a599c0157634fc707e28a.jpg
And here's my crank position...
Here's someone from the Malibu forums with a similar issue (skip down to the last couple of posts).
http://www.themalibucrew.com/forums/index.php?/topic/43900-383-hammerhead-rebuild/page-2
...
I'm positive it's mefi 5. Very strange, I wonder why it's so far off.
Sent from my iPhone using Tapatalk
Yep, 650 degree cam angle. That's what diacom is reporting.
According to this, I should be at 705.
https://www.bakesonline.com/images/MediaLibrary/IndmarIgnitionTiming.pdf
Sent from my...
I got the rockers adjusted today, which seems to have solved the ticking/clicking noise I heard. I also got my raw water pump installed again, to find out that the rear seal is leaking -_-
As for...
I was told to use cardboard to create the template. That said, I ended up paying someone to do the stringers in my old boat (87 Invader 16ft), it cost a few hundred for both. It wasn't a great job...
So, I finally had a chance to get back and deal with the timing issue. I was definitely 180 out, long story short, I got the motor running today. I didn't run it long, but I did bring it up to 1200...
I was feeling left out of the whole winterizing fun, so I decided to winterize South Florida style. I threw the heavy cover on :D
...
Now that I think about it, I was basing it on when the valve closest to the stern (front of engine) would go up. With out checking any pictures, Im almost that is the exhaust valve. :)
Sent from...
I understand now. I'll check that next time I'm near the boat.
Sent from my iPhone using Tapatalk
Both valves are in the up position. There is a mark on the balancer and the housing. I lined those up to ensure TDC. I lined up the indent and white line on the distributor and dropped the...
Wakeboarding in the ocean is a bit tough unless it's really calm, but we have gone down the the Florida keys and wakeboard end in the Gulf of Mexico/Florida bay early in the morning. Usually we...
So I got everything put back together a few weeks back, but I've been struggling to get the motor to show any signs of life.
Primed the oil galleys with the priming tool and drill.
I have...
Where in Florida? I might be able to swing by and look at it if it's within a couple hours of Miami.
Sent from my iPhone using Tapatalk
You should be able to turn the cylinders by "hand". To do this, you will need to attach a socket (24mm I believe) and breaker bar (you can use a normal ratchet with a pipe on it to get leverage, but...
I replaced my lifters while I had the heads off, a few were collapsed and others I thought may be going so I did all 16.
Sent from my iPhone using Tapatalk
Here are the pictures
http://images.tapatalk-cdn.com/15/10/19/d5b3a165464e7550a259b1b7014947b0.jpg
http://images.tapatalk-cdn.com/15/10/19/ae254470303ca55528154b1c26c88a0c.jpg
...
Don't mean to hijack the thread, but 2500 are those the same injectors for the 2006? Do you have a part number?
Sent from my iPhone using Tapatalk