Thanks Chris,
I just sent it over.
Type: Posts; User: tstruth
Thanks Chris,
I just sent it over.
Just the filler tube. It was the only way I could get to the three long bolts that hold down the metal connector that secures the gas cap. You will need to disconnect that from the filler hose. I...
Hello All,
I am having some trouble figuring out how the red breaker in the back connect to the solenoid. I had to disconnect a few things in the beginning of the season with the ignition and fuse...
It was a little tricky. Be sure to drain all the gas first for you have to tip it to get the hose from the fill spout out. I had to do a little cutting to the side panel to get too the clamps that...
I just finished doing the same replacement with the rudder. I had to drill out a 2inch hole. When I reinstalled the gas tank it was sitting on top of the rudder assembly. It was a little taller than...
Thanks for the advise. I think I will go with the 14 Gang Sierra.
Not sure how many more years I am going to get out of her. She needs some tlc. I would love to give it a make over like yours Jet.
Does anyone know where I can find a fuse panel for an 86 Supra comp?
I seem to be having trouble with it. Connections are rusting and breaking.
Thanks
Thanks I will give it a try.
Hello Folks,
Started the engine and it sounded like the starter was staying engaged. I turned off the key but the engine stayed running. I swapped out the ignition switch and still the same. I...
I just want to give an update on the transmission rebuilt. I put much thought in to doing the inner clutch plates on the ring gear since I had it all apart on the bench but the inside of the...
Do you think that is the reason for no reverse? Wondering if I should replace the clutch plates or leave it alone. They whole unit looks clean. Also the hole in the forward and reverse adapter...
Another picture15791
Got it apart. Seems like the plate pressure springs had some issues. Three of them were broken in two pieces and caused some damage to the friction clutch plate. The others springs were bent and...
I have been tapping pretty hard for a couple hours now. Lubricating and tapping, nothing but a tired arm. Would i cause any damage if I applied heat?
I finally have my transmission on the bench ready for the dismantling. I am having difficulty removing the Pump housing. The four bolts are removed but not sure why she won't release. Is there...
Thanks guys for the reply. I have never taken apart a transmission but I am looking forward to seeing how this thing works. I have the boat up in New Hampshire and have a couple of more weekends...
Seems I have the same problem with my 1986 Supra Comp TS6 w/ a 351W. Forward but no reverse. When I put it in reverse she just idles up. I could use some advice on where to by the parts and any...
Hi Folks,
I have a 1986 Supra Comp TS6 w/ a 351W with a tranny problem. No reverse, but forward works fine. The fluid was brown and milky. I tried draining the fluid and trying new. No luck. From...
Hey guys,
I have the same problem. I thought it might be a overheating issue. Changed impeller and still the same. Set points and timing 6 BTC. Still the same. New coil, still the same. Cold she...
Hey guys,
New issue. Bilge pump control switch died. Checked the connections and she needs to be replaced. The other switches are malfunction as well so I think i will replace all. Does anyone...
Reset the points and timing. She runs sweet. Speed increased from 37 to 44.
Motor sounds strong.
Thanks again guys for all the help.
I will reset them and try that first. Fuel is a couple of weeks old. What's up with the water spray? what am I looking for?
Thanks for the reply guys.
When I first started going it happened at slow speed. I gave it a little throttle and it happened again. Not all the time just a couple. Then I opened it up and it seemed fine until I brought it down...
Hey folks,
I have my Comp back together and sitting in the water. Took her out today and she ran well, Top speed was around 40. Had a little miss firing going on. Pulled the plugs and checked the...
Hey Folks,
Where can I find the best deal on a cover for my 1986 Supra Comp? Custom snug fit.
The one I am using puddles up water in the back and if it rains hard I can see this baby ripping.
...