Search:

Type: Posts; User: michael hunter

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds; generated 13 minute(s) ago.

  1. Replies
    1
    Views
    30

    I switched from the Vault system to marine grease...

    I switched from the Vault system to marine grease and bearing buddies on my 08 .
  2. No doubt the engine is misaligned or the strut is...

    No doubt the engine is misaligned or the strut is bent. After 30 years I would be surprised if it didn't need stringers. You said the engine ran fine the compression numbers are a little low but also...
  3. Replies
    3
    Views
    285

    My 2008 Boatmate trailer came with the Vault...

    My 2008 Boatmate trailer came with the Vault bearing system after a few years the caps would blow out ans leak grease all over. I went back with standard wheel bearing grease and trailer buddy...
  4. Replies
    9
    Views
    711

    Where are you located? I have 2 to compare to.

    Where are you located? I have 2 to compare to.
  5. Do the holes go through both upper and lower...

    Do the holes go through both upper and lower hulls? Push the filler through both hulls . Only problem is if you ever have to take the cap off.
  6. Replies
    13
    Views
    1,385

    Go with AC spark plugs don't get fancy with some...

    Go with AC spark plugs don't get fancy with some smoke and mirrors brand . Never use Champion in a GM.
  7. Replies
    9
    Views
    711

    Your comp originally had open cell foam under the...

    Your comp originally had open cell foam under the floor they are known to absorb water especially ones that are left out in the rain. Your comp weighed 2350 lbs when new. Have it weighed and subtract...
  8. Replies
    9
    Views
    1,078

    Mine is 6''x14''x60'' its out of a comp

    Mine is 6''x14''x60'' its out of a comp
  9. Replies
    13
    Views
    1,385

    That engine only has 800 hours its not even close...

    That engine only has 800 hours its not even close to worn out. What problems are you having with it?
  10. Why don't you mix some epoxy mixed with cabosil...

    Why don't you mix some epoxy mixed with cabosil to thicken it and fill the holes.
  11. Replies
    9
    Views
    1,078

    I will check today.

    I will check today.
  12. Replies
    13
    Views
    1,385

    Not a fan of MSD ignition definitely not a fan of...

    Not a fan of MSD ignition definitely not a fan of the butt connectors on the red and black wires. The correct plug is a AC MR43T. The MR45T will run a little hotter.
  13. Replies
    13
    Views
    1,385

    What year and engine do you have?

    What year and engine do you have?
  14. Replies
    9
    Views
    1,078

    I have one out of a comp. Can you measure yours?

    I have one out of a comp. Can you measure yours?
  15. Replies
    5
    Views
    1,345

    post the pics on imgur then copy and paste them...

    post the pics on imgur then copy and paste them here.
  16. How much old gas is in it. Sounds like bad gas?

    How much old gas is in it. Sounds like bad gas?
  17. I have a flat angle one off a 86 comp .

    I have a flat angle one off a 86 comp .
  18. Replies
    4
    Views
    1,655

    Check the fuel pump

    Check the fuel pump
  19. Replies
    15
    Views
    4,938

    They are actually circuit breakers . They will...

    They are actually circuit breakers . They will pop if something goes wrong with the circuit. You can also use them for a switch if you push down on them. They do go bad after years skidim keeps them...
  20. Replies
    1
    Views
    927

    Its not a air cleaner its a flame arrester ....

    Its not a air cleaner its a flame arrester . Modifying or removing it will get you a ticket if you are pulled over and inspected. Not to mention the risk of fire. Make sure its clean and don't mess...
  21. Replies
    15
    Views
    4,938

    You can get new push button dash switches from...

    You can get new push button dash switches from Skidim . Supra wiring is a birds nest at best I would not want to try to change for different style switches. Somebody has already been in there the...
  22. Replies
    4
    Views
    2,038

    I always just remove the hose at the hull inlet...

    I always just remove the hose at the hull inlet fitting stick it in a bucket and put a garden hose in the bucket . Adjust the water flow to the amount of water the engine is taking so you don't...
  23. Replies
    2
    Views
    940

    Go to Skidim.

    Go to Skidim.
  24. It should have been a stainless steel bolt the...

    It should have been a stainless steel bolt the housing is brass corrosion should not have been a factor. Use a little heat and vice grips to get the old bolt out.
  25. Replies
    15
    Views
    4,938

    That is a 454 GM engine. Why do you need to...

    That is a 454 GM engine. Why do you need to replace it? Are you sure its a Sunsport? Most Sunsports have a 351w.
Results 1 to 25 of 498
Page 1 of 20 1 2 3 4