Page 5 of 5 FirstFirst ... 345
Results 41 to 48 of 48
  1. #41

    Default

    Got it out finally. Lots of adhesive to get off. Any great ideas how to remove and clean? Also seals look good and it looks like the grease coming out was through a small pinhole in bottom of flange. Anybody know the purpose of this hole? When I reinstall, what should I use to seal everything?


    Sent from my iPhone using Tapatalk

  2. #42
    Join Date
    Dec 2016
    Posts
    208

    Default

    The seals are cheap...replace them while you have it out. I would also replace the snap rings, or at least remove and check their condition. Mine were rust welded in place...you can search for my thread were I rebuilt mine and see pics of what I'm talking about. There's also a picture in that thread of the tool used to clean it up.

    The hole is where a grease zerk screws in.

  3. #43

    Default Repairing a older style rudder port

    Any chance my model does not use snap rings? I don't have it in front me of me but the only thing in the housing was two o rings to the best of my knowledge.

    Also, still trying to figure the purpose of this small pinhole that the grease came out of. It is on hull side near where rudder shaft gets inserted. It is not the grease zirc. That goes on engine side. I'm thinking it is just a grease relief if it is too full. Concerned however this setup would allow water into the housing


    Sent from my iPhone using Tapatalk
    Last edited by torch; 06-09-2017 at 01:37 AM.

  4. #44
    Join Date
    Dec 2016
    Posts
    208

    Default

    Quote Originally Posted by torch View Post
    Any chance my model does not use snap rings?
    LOL, you totally threw me off with your post title of "repairing old style" rudder. My boat is ~13 yrs older than yours. Worst case you can drop $500 at any number of online shops and have a full turnkey replacement, otherwise you may have to reverse engineer it yourself and post up the DIY.

    Others on here may definitely be able to help but you may want to post some pics to help illustrate the questions you have.

  5. #45
    Join Date
    Aug 2010
    Location
    NJ
    Posts
    1,375

    Default

    My '89 Saltare had a packing gland for the rudder and just brass on brass of the rudder port to post, no provisions for grease. It wore out as there was a fair amount of slop in the assembly. Not sure which style you have, but I ended up replacing mine with the large Mastercraft rudder which has about teh same surface area. Performs great! If mine was rebuildable and not excessively worn I would have just rebuilt it but that wasn't an option unfortunately. My thread on rudder replacement: https://forum.supraboats.com/showthr...er-replacement

  6. #46
    Join Date
    Feb 2020
    Posts
    2

    Default

    Thanks for the information, does anybody know if the snap ring has to be removed in order to remove the oil seals?

  7. #47
    Join Date
    Sep 2010
    Location
    Collegedale, TN
    Posts
    1,901

    Default

    Quote Originally Posted by Rafamonc View Post
    Thanks for the information, does anybody know if the snap ring has to be removed in order to remove the oil seals?
    Yes, it does.

    1986 Saltare
    Restoration link: http://supraboats.com/bbs/showthread.php?t=7839

  8. #48
    Join Date
    Sep 2008
    Location
    Parkersburg, WV
    Posts
    1,911

    Default

    Some of the original Supras used a packing gland, others had a mechanical seal with o-rings, grease seals and snap rings holding it together. Mine is the latter, and somewhere there's an old thread I posted showing diagrams and parts needed when I rebuilt mine probably 7 or 8 years ago.

    Just realized that old diagram is part of this thread ... it was 2014. Wow!! I hope it has helped someone out there over the years.

    Sent from my SM-G973U using Tapatalk
    Last edited by csuggs; 05-04-2021 at 08:24 PM.
    Clint
    Wake the World - West Virginia
    www.waketheworldwv.com

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •