Page 1 of 2 12 LastLast
Results 1 to 10 of 13
  1. #1
    Join Date
    Dec 2015
    Location
    Madison, AL
    Posts
    115

    Default Building Subwoofer Enclosure

    I'm getting ready to tackle building a sealed subwoofer enclosure. Currently I have a 4 ohm 10" Kicker sub running off the sub channel on my Kicker ZX700.5 amp in free air space up under the helm. Thinking that I'll get a 2 ohm Kicker and put it in a sealed box I build.

    After doing a little research I think I'm going to use exterior grade MDF to construct the box and coat it in fiberglass.

    Any suggestions or input before I get started would be appreciated.
    David
    2011 Supra Launch 242

  2. #2
    Join Date
    Apr 2012
    Location
    Lake Wylie NC Area
    Posts
    440

    Default

    Got room to do two? A pair of KM-10 in a 1.8 sealed splitting 420W rms is quite impressive.

    Other wise, if you are going to go with another woofer for a 2 ohm coil, go with a 12" Enclosure volume would be about the same, just need 2" more height and width over a 10". That extra surface are will do more than getting that extra 200W from the amp.

    Im a birch man myself. Go with a 2-part resin over fiberglass. Build the box right and you wont need additional strength from fiberglass, just need waterproofing.
    Michael
    Mikes Liquid Audio

  3. #3
    Join Date
    Dec 2015
    Location
    Madison, AL
    Posts
    115

    Default

    Quote Originally Posted by Wylietunes View Post
    Got room to do two? A pair of KM-10 in a 1.8 sealed splitting 420W rms is quite impressive.

    Other wise, if you are going to go with another woofer for a 2 ohm coil, go with a 12" Enclosure volume would be about the same, just need 2" more height and width over a 10". That extra surface are will do more than getting that extra 200W from the amp.

    Im a birch man myself. Go with a 2-part resin over fiberglass. Build the box right and you wont need additional strength from fiberglass, just need waterproofing.
    Hey Mike,
    Thanks for the feedback. Box area that I have under the helm is approx. 20" tall x 23" wide x 10" deep. I am intrigued about the idea of doing (2) Km-10's. And birch would definitely be less expensive than the exterior grade MDF. If I do the birch, do I need to use the fiberglass or can I just do the 2-part resin and call it done? Also in wiring (2) subs together, I'm guessing that the wires running from the amp to the speakers go (1) to positive and (1) to negative of the two subs and then wire from positive to negative between the (2) subs, correct?

    Thanks for your help.
    David
    2011 Supra Launch 242

  4. #4
    Join Date
    Apr 2012
    Location
    Lake Wylie NC Area
    Posts
    440

    Default

    @ 23W two KM10 will fit side by side, but they will be close. @ 23 x 20 10, you internal volume couldnt be more ideal.

    Make sure you get the higher quality birch. Its usually void-free as compared to the lower grade used for subfloor construction. No fiber glassing, just a quality 2-part marine waterproofing.

    If your current woofer is a 4 ohm, which I would expect if it was the OEM woofer in 2011, then you would get a new 4 ohm and they would be wired in parallel and then connected to the existing speaker wire.

    Your original woofer likely has a silver grill. The new ones will come with choice of charcoal, white or chrome and they look different. If you ask around, you might find a kicker dealer thats got spare KM-10 grills so you could match the old to the new. Just note, the cone of the woofers look a little different. Once the install is done, I dont think the difference will be noticeable.
    Michael
    Mikes Liquid Audio

  5. #5
    Join Date
    Nov 2011
    Location
    Paris, France
    Posts
    536

    Default

    Hi David,
    I built mine in 3/4" expanded PVC sheet :



    No issue for years. It's completly water friendly.
    Stéphane
    -----------------------
    1989 Supra Saltare

  6. #6
    Join Date
    Dec 2015
    Location
    Madison, AL
    Posts
    115

    Default

    Got started on the enclosure today. Ordered a second Km-10 and a bass remote control knob. Looking for a good supplier of 2-part epoxy resin. Any suggestions? I'm thinking I'll add pigment to the epoxy to be able to achieve the finish look I want.
    Last edited by 4alkings; 08-05-2016 at 10:07 PM.
    David
    2011 Supra Launch 242

  7. #7
    Join Date
    Dec 2015
    Location
    Madison, AL
    Posts
    115

    Default

    Here are some pics from the build so far. Box is built (glued, screwed, inside edges sealed with silicone). Went with (2) Kicker 4 ohm subs. Waiting for 2 part epoxy to arrive tomorrow. Will update more later.
    Sub Box 1.jpg
    Sub Box 2.jpg
    David
    2011 Supra Launch 242

  8. #8
    Join Date
    Dec 2015
    Location
    Madison, AL
    Posts
    115

    Default

    Here is a pic after apply 2- part epoxy inside and out. After epoxy set, I primed the outside of the box with 3 coats of Aluthane (aluminum impregnated urethane). Bonding and leveling qualities are fantastic. Aluthane is waterproof and UV resistant. Trying to decide if I will leave it as is or top coat it with a urethane paint and clear coat.

    Sub Box Primed.jpg
    David
    2011 Supra Launch 242

  9. #9
    Join Date
    Dec 2015
    Location
    Madison, AL
    Posts
    115

    Default

    Took the time this afternoon to pull the original sub and panel. Installed the new sub enclosure with (2) Kicker KM10's. Looks and sounds fantastic to me.

    Subbox installed.jpg
    David
    2011 Supra Launch 242

  10. #10
    Join Date
    Dec 2015
    Location
    Madison, AL
    Posts
    115

    Default

    Here is a video file. Working on dialing it in.

    David
    2011 Supra Launch 242

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •