Quote Originally Posted by Jetlink View Post
Haugy, what are your plans for wet sanding on that comp of yours?
Well the owner is being a wimp and won't deliver it. Friggin yanks.


Quote Originally Posted by Okie Boarder View Post
I've been eyeing the bottom on mine, while I've been working on it. That will be next. Did you go around the areas it makes contact with the trailer or lift it up somehow? Did you jusy lay under the boat or use a creeper? How much of an area are you finding you can cover before the sanding disks are worn and what discs are you using?
On the bow I used a jack and a block of wood right under the lower bow eye, using the metal eye as my lifting point. That allowed me to lift the bow enough to remove the padding on the bow riser.

For the back I'll be using an engine hoist (cherry picker). Mine is very big......hee hee..... so I can lift the boat enough to put it on blocks. I've got big pieces of 6x6 scrap wood that I will lay across the two side bunks on each side. Perpendicular to the run of the bunks. I'll put 3 in place on one side. Sand and wax those areas, move the 6x6s to get under them as well, and then switch sides. I haven't done it yet as I got all the way to the skeggs and stopped. I'll probably finish it out later in the fall. But the bow area is bright white now.

I used 3m pads. For the hand stuff I just used good ole 3M black sandpaper you can find at any automotive place. But for the 1000,1500, etc I had to go with 3M Trizect pads. They are the only ones that have that grit range, and hook and loop fasteners so when wet they won't come off. BE WARNED: They are expensive as hell. Each pad was about $3. And the 3000 grit pads are $10 each. A heads up, the pads feel like toilet paper. They are super smooth and soft. You wouldn't think they could cut anything, but they actually work very well.

I used 8 1000 grit pads to do the lower sides (under the colored gel-coat) and the bottom of the boat to the skeggs. Probably could have used 10 and it would have been better. I bought 2 of the 3000 grit and they seemed to do well, but that was stretching it. 3 probably would have sufficed. All in all I think I had about $130 in sandpaper. OUCH. But the benefit of knocking one grit range out each night was worth it. I would go out with 1000 grit, and an hour and a half later I was done. Next night, 1500. To get that done in that time frame was worth it.

With the trizect pad I learned that it's good to keep the pad clean, but not the boat as much. Allowing some of the grit to work with the pad helped it cut. So I would hose the area I was about to work, and then wouldn't hose it again unless I was done working it. I kept the pad pretty clean though, rinsing after a couple of minutes or 2 sq/ft of work.

I did try an experiment just to see how it would do. In the lower part of the keel I went from 1000 grit to 3000 grit to see how it would do. It's very white, but not near as glossy as the rest. I would make sure to put some grits in between and not short-cut it if you want high-gloss. It will work for the rest of the season, but I will be going back and redoing it later with 1500+ grit and finishing it out again.

With the air sander you don't need a lot of speed, most of the time I had it so it would slowly turn if I just held it to the side. No pressure, just placed on the side of the boat. Then when I put pressure on, it wasn't spinning just orbiting. Higher speed will eat your pad up.

I didn't use a creeper as I needed to be able to maintain constant pressure and at odd angles. Having wheels under me would have just kept pushing me away from the boat. When I got up high on the front I raised up the boat so I could sit indian style under the boat. When I worked my way back I lowered it so when I was on my back I could easily reach the hull without overextending my arms.

I'll get pics this weekend as I'm taking it out to WakeFest this weekend. It is a great improvement over how it's looked since I got it.