Tab Content
  • Hagman's Avatar
    05-06-2021, 10:44 PM
    Hagman replied to a thread supra comp ts6m in General Chat
    My dealer pugged that hole before took the boat home. He said it was a stupid idea that would lead to premature stringer rot. There's always a towel...
    10 replies | 414 view(s)
  • Jetlink's Avatar
    05-04-2021, 10:05 AM
    I have a 160 degree thermostat on my boat as well and running it on the hose I never see anything above 140 and on the water I see 150-160 usually in...
    5 replies | 156 view(s)
  • Jetlink's Avatar
    05-04-2021, 10:02 AM
    Jetlink replied to a thread Boat Lift Cradle in General Chat
    You are going to want to do some modifications to that lift as the skegs, strut, prop shaft, prop and possibly rudder will all interfere with that...
    4 replies | 215 view(s)
  • Jetlink's Avatar
    05-04-2021, 09:57 AM
    Jetlink replied to a thread supra comp ts6m in General Chat
    Since when? I was able to get a brand new one from Skiers Choice a few years back when I did my restoration. Anyway, I did not drill a hole in the...
    10 replies | 414 view(s)
  • Jetlink's Avatar
    04-26-2021, 09:16 PM
    Changing the oil before layup at the end of the season is best as the oil is fresh. As you run the engine, the oil builds acidity and that then sits...
    5 replies | 233 view(s)
  • Jetlink's Avatar
    04-19-2021, 09:51 AM
    Upgrading? Give me a shout when you are back up here again end of May.
    1 replies | 256 view(s)
No More Results

3 Visitor Messages

  1. Hey! I would like to advise nursing essay writing service uk to simplify the learning process. I myself constantly resort to their help, and I can say with confidence that you will not find any plagiarism, everything will be completed on time. I advise you to pay attention
  2. View Conversation
    hagman,
    saw your post to a rudder question...replied to it...but i'm not sure if it goes to you. sorry if this is duplicate. my 95 labrisa lost surprise fight with rock and i had to put on all new undergear on her.....the new rudder assembly from skidim steers much easier than original, but pulls pretty hard to the right. can you explain the 'filing the back edge' process to minimize this?
    thanks,
    james
  3. View Conversation
    That is what I'm going to do also. My brother-n-law has been helping me out a lot. He's got the big "shop". I'm on the floor this week, and once that is in I'll get it sprayed with...http://www.gatorhydemarine.com/ I'm doing the floor charcole and the outside black. I'll be keeping the seats for now, but will have them done someday??$$$
Showing Visitor Messages 1 to 3 of 3
About Hagman

Basic Information

About Hagman
Location:
Oregon
Occupation:
Builder

Statistics


Total Posts
Total Posts
302
Posts Per Day
0.08
Visitor Messages
Total Messages
3
Most Recent Message
04-22-2021 11:14 AM
General Information
Last Activity
05-06-2021 10:49 PM
Join Date
06-26-2010
Referrals
0

8 Friends

  1. jet jet is offline

    Senior Member

    jet
  2. Jetlink Jetlink is offline

    Moderator

    Jetlink
  3. lively lively is offline

    Senior Member

    lively
  4. ludacris ludacris is offline

    Junior Member

    ludacris
  5. mapleleaf mapleleaf is offline

    Senior Member

    mapleleaf
  6. Ontarion Ontarion is offline

    Member

    Ontarion
  7. rlhahn rlhahn is offline

    Member

    rlhahn
  8. rludtke rludtke is offline

    Senior Member

    rludtke
Showing Friends 1 to 8 of 8